Statistical Analysis and Predictive Modelling of Chip Temperature in the Cutting Zone for Tools with Different Rake Angles
Materials · 06.11.2026 · 19 (21) · 4728
DOI: 10.3390/ma19214728 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 06.11.2026. Verfasst von Ireneusz Zagórski und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Production Engineering, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Lublin University of Technology.
Abstract (Originalsprache)
Experimental thermographic data from dry rough milling of AZ31B and AZ91D magnesium alloys using tools with rake angles of 5° and 30° were reanalysed using descriptive statistics and predictive modelling. Depending on the assumptions of normality and homogeneity of variance, a one-way ANOVA, Welch ANOVA or Kruskal–Wallis test was applied to up to ten highest available readings of each run; as these are repeated measurements within a run, the tests are interpreted descriptively and supplemented with effect sizes. Descriptive comparisons showed differences in the selected upper-temperature readings across parameter levels within the alloy–rake-angle groups. To provide a consistently defined upper-tail response, whose estimation precision depends on the number of recorded frames, the 95th percentile (T95) of the thermographic observations was adopted as the predictive response. Gaussian process regression (GPR) was evaluated using leave-one-out cross-validation and a clipped jackknife+-type procedure. The cutting-speed paths had the lowest mean absolute prediction error (9.7 °C), compared with 17.7 °C for feed per tooth and 18.7 °C for axial depth of cut. The nominal 95% GPR prediction intervals achieved only 63.4% mean empirical coverage, increasing to 85.2% with the clipped procedure, which has no standard coverage guarantee and remains below the nominal level. Linear and quadratic regression provided comparable point-prediction accuracy and, with the same clipped procedure, comparable coverage (85.2% and 86.6%), whereas a shallow neural network performed worse. Increased model complexity did not consistently improve prediction in this dataset. These results demonstrate that assessment of chip-temperature models requires out-of-sample validation and explicit calibration of predictive uncertainty.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Production Engineering, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland.
- Department of Organisation of Enterprise, Faculty of Management, Lublin University of Technology, 20-618 Lublin, Poland.
- Institute of Machine Tools and Production Engineering, Faculty of Mechanical Engineering, Lodz University of Technology, Stefanowskiego 1/15, 90-537 Łódź, Poland.
- Institute of Mechanical Technology, Faculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 2, 61-138 Poznań, Poland.
ORCID-Profile: Ireneusz Zagórski, Monika Kulisz, Agnieszka Skoczylas, Piotr Zgórniak, Stanisław Legutko
Förderung
- Lublin University of Technology
Zitieren
APA
Zagórski, I., Kulisz, M., Skoczylas, A., Zgórniak, P., & Legutko, S. (2026). Statistical Analysis and Predictive Modelling of Chip Temperature in the Cutting Zone for Tools with Different Rake Angles. Materials, 19(21), 4728. https://doi.org/10.3390/ma19214728
Vancouver
Zagórski I, Kulisz M, Skoczylas A, Zgórniak P, Legutko S. Statistical Analysis and Predictive Modelling of Chip Temperature in the Cutting Zone for Tools with Different Rake Angles. Materials. 2026;19(21):4728. doi:10.3390/ma19214728
BibTeX
@article{Zagrski2026,
author = {Zagórski, Ireneusz and Kulisz, Monika and Skoczylas, Agnieszka and Zgórniak, Piotr and Legutko, Stanisław},
title = {Statistical Analysis and Predictive Modelling of Chip Temperature in the Cutting Zone for Tools with Different Rake Angles},
journal = {Materials},
year = {2026},
volume = {19},
number = {21},
pages = {4728},
doi = {10.3390/ma19214728}
}
EUVIMED