EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Finite Element Modeling of Quenching Residual Stress in GH4169 Alloy Turbine Disk Forgings

Haoyu Lu, Shengjie Wang, Yang Li, Haijiang Dong, Ying Yu, Shilei Li iD, Chunlei Zhao

Materials · 28.10.2026 · 19 (21) · 4544

DOI: 10.3390/ma19214544 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 28.10.2026. Verfasst von Haoyu Lu und 6 weiteren Autor:innen. Beteiligte Einrichtung: China United Test & Certification Co., Ltd., Beijing 101407, China. Die Arbeit nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A finite element model was established to investigate the formation mechanism and evolution behavior of quenching residual stress in GH4169 alloy turbine disk forgings, and the model was validated by X-ray diffraction and hole-drilling measurements. The results show that the evolution of quenching residual stress can be divided into three stages, and the stress distribution is closely related to the temperature gradient and plastic deformation. During quenching, the stress state gradually changes from “inner compression–outer tension” to “inner tension–outer compression”. After quenching, the residual stress field is characterized by surface compressive stress and internal tensile stress, with the maximum compressive and tensile stresses reaching about −794 MPa and +720 MPa, respectively. Both equivalent stress and equivalent plastic strain show high values in the surface and core regions and low values in the transition region. Their maximum values appear at the disk surface, reaching 733.4 MPa and 6.018%, respectively. Further analysis indicates that the spatial and temporal evolution of plastic strain is strongly dependent on the temperature gradient. The incompatible plastic deformation induced by the temperature gradient is the dominant mechanism for quenching residual stress formation, while the accumulation of plastic strain directly determines the magnitude and distribution of the residual stress. The relative deviation between the simulated and measured residual stresses is about 15%, which is within the acceptable range for engineering simulation, confirming the reliability and engineering applicability of the established model.

Schlagwörter

Stichwörter der Autor:innen

GH4169 superalloyfinite element simulationresidual stressturbine disk

Autor:innen und Institutionen

  • China United Test & Certification Co., Ltd., Beijing 101407, China.
  • United (Chongqing) Test & Certification Co., Ltd., Chongqing 400700, China.
  • Guobiao (Beijing) Testing & Certification Co., Ltd., Beijing 101407, China.
  • State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083, China.

ORCID-Profile: Shilei Li

Förderung

  • National Key Research and Development Program of China

Zitieren

APA

Lu, H., Wang, S., Li, Y., Dong, H., Yu, Y., Li, S., & Zhao, C. (2026). Finite Element Modeling of Quenching Residual Stress in GH4169 Alloy Turbine Disk Forgings. Materials, 19(21), 4544. https://doi.org/10.3390/ma19214544

Vancouver

Lu H, Wang S, Li Y, Dong H, Yu Y, Li S, et al. Finite Element Modeling of Quenching Residual Stress in GH4169 Alloy Turbine Disk Forgings. Materials. 2026;19(21):4544. doi:10.3390/ma19214544

BibTeX
@article{Lu2026,
  author = {Lu, Haoyu and Wang, Shengjie and Li, Yang and Dong, Haijiang and Yu, Ying and Li, Shilei and Zhao, Chunlei},
  title = {Finite Element Modeling of Quenching Residual Stress in GH4169 Alloy Turbine Disk Forgings},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {21},
  pages = {4544},
  doi = {10.3390/ma19214544}
}
Kostenlos starten →