EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Beyond Poisson’s Ratio: Material–Process Performance of Additively Manufactured Auxetic Lattices

Barbara Schürger iD, Michal Hovanec iD, Peter Palička iD, Robert Szaniszló

Materials · 26.10.2026 · 19 (21) · 4506

DOI: 10.3390/ma19214506 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 26.10.2026. Verfasst von Barbara Schürger und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Aviation Engineering, Faculty of Aviation, Technical University of Košice, Rampová 1731/7, 040 01 Košice, Slovakia. Die Arbeit nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Program Slovensko.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Auxetic lattices are usually tailored through geometry, whereas the effect of the constituent material and manufacturing route at fixed architecture has received little replicated experimental attention. One re-entrant lattice design was produced in nine material/process variants and tested in quasi-static tension (10 specimens per variant, N = 90): polylactic acid (PLA), impact-modified PLA, glycol-modified polyethylene terephthalate (PETG), acrylonitrile butadiene styrene (ABS), acrylonitrile styrene acrylate (ASA), UltraT and Flex 3D by fused deposition modeling (FDM), and polyamide 12 (PA12) by FDM and by selective laser sintering (SLS). Maximum force Fmax, crosshead displacement at peak load u(Fmax), archived structural stiffness k and mechanical work W14 up to 14 mm displacement depended strongly on the variant (p < 0.001; Kruskal–Wallis ε2 = 0.908–0.942). PLA reached the highest mean Fmax (68.48 ± 2.40 N), whereas PETG accumulated the highest mean W14 (622.80 ± 28.03 N mm), 7.9% more than PLA (95% simultaneous confidence interval 1.2–14.5%), despite a 4.3% lower Fmax. SLS PA12 exceeded FDM PA12 by 11.0% in Fmax and by 21.9% in W14. The W14 ranking refers to the 14 mm limit, and k is interpreted as an archived descriptor. Previously processed optical measurements gave effective Poisson’s ratios of −1.043 to −1.052 for eight variants; these values are reported descriptively, and a linear finite-element model illustrates the auxetic mechanism. Force, displacement at peak load and mechanical work should therefore complement Poisson’s ratio in material selection for auxetic lattices.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingauxetic metamaterialsmaterial extrusionmaterial selectionmechanical worknegative Poisson’s ratiore-entrant latticeselective laser sintering

Autor:innen und Institutionen

  • Department of Aviation Engineering, Faculty of Aviation, Technical University of Košice, Rampová 1731/7, 040 01 Košice, Slovakia.
  • Department of Applied Mechanics and Mechanical Engineering, Faculty of Mechanical Engineering, Technical University of Košice, Letná 1/9, 042 00 Košice, Slovakia.

ORCID-Profile: Barbara Schürger, Michal Hovanec, Peter Palička

Förderung

  • Program Slovensko

Zitieren

APA

Schürger, B., Hovanec, M., Palička, P., & Szaniszló, R. (2026). Beyond Poisson’s Ratio: Material–Process Performance of Additively Manufactured Auxetic Lattices. Materials, 19(21), 4506. https://doi.org/10.3390/ma19214506

Vancouver

Schürger B, Hovanec M, Palička P, Szaniszló R. Beyond Poisson’s Ratio: Material–Process Performance of Additively Manufactured Auxetic Lattices. Materials. 2026;19(21):4506. doi:10.3390/ma19214506

BibTeX
@article{Schrger2026,
  author = {Schürger, Barbara and Hovanec, Michal and Palička, Peter and Szaniszló, Robert},
  title = {Beyond Poisson’s Ratio: Material–Process Performance of Additively Manufactured Auxetic Lattices},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {21},
  pages = {4506},
  doi = {10.3390/ma19214506}
}
Kostenlos starten →