Microstructure and Shear Strength of SiC Joints Brazed with a Si–Ti–Al Filler Alloy
Materials · 19.09.2026 · 19 (18) · 3990
DOI: 10.3390/ma19183990 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 19.09.2026. Verfasst von Lianfeng Wei und 6 weiteren Autor:innen. Beteiligte Einrichtung: National Key Laboratory for Science and Technology on Reactor and Materials, Nuclear Power Institute of China, Chengdu 610041, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Investigation on the Mechanical Properties and Microstructure Regulation of SiCf/SiC Composite Joints Brazed at Ultra-High Temperatures, National Natural Science Foundation of China, Natural Science Foundation of Henan Province, China.
Abstract (Originalsprache)
The joining of solid-state sintered silicon carbide (SiC) was achieved using a novel Si-Ti-Al ternary alloy via vacuum brazing. This study investigates a predominantly non-carbide-dominated interfacial bonding mechanism and the influence of brazing temperature on joint microstructure, mechanical properties, and high temperature reliability. The high Si content promoted the incorporation of Ti into Ti–Si phases within the brazed seam, thereby limiting the amount of Ti available for reaction with SiC. No continuous TiC layer was detected within the spatial resolution of the employed characterization methods. Minor discrete Al4C3 precipitates were identified at the interface but did not constitute the dominant bonding phase. Brazing at 1360 °C yielded an optimal microstructure featuring highly regular coral-like eutectic clusters, resulting in a peak room temperature shear strength of 102.8 MPa. The joints also exhibited favorable high temperature reliability, maintaining a shear strength of 58.4 MPa at 1000 °C. Microstructural analysis following thermal exposure revealed partial coarsening of primary blocky phases and interfacial Al4C3 precipitates via Ostwald ripening, which contributed to the reduction in high temperature strength. Nevertheless, the robust retention of fine eutectic clusters ensured satisfactory structural stability under thermal loading. This work provides a viable strategy for designing Si-based brazing fillers for high-performance SiC ceramic joining.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- National Key Laboratory for Science and Technology on Reactor and Materials, Nuclear Power Institute of China, Chengdu 610041, China.
- Zhengzhou Advanced Research Institute, Harbin Institute of Technology, Zhengzhou 450000, China.
Förderung
- Investigation on the Mechanical Properties and Microstructure Regulation of SiCf/SiC Composite Joints Brazed at Ultra-High Temperatures
- National Natural Science Foundation of China
- Natural Science Foundation of Henan Province, China
- China Postdoctoral Science Foundation
- Natural Science Foundation of Heilongjiang Province, China
- Key Scientific and Technological Program of Henan Province, China
- the Special Fund for Key Breakthrough Projects in Priority Areas
- Special Fund for Key Breakthrough Projects in Priority Areas
Zitieren
APA
Wei, L., Lv, Z., Xu, R., Zhao, Y., Wang, C., Zheng, Y., & Li, X. (2026). Microstructure and Shear Strength of SiC Joints Brazed with a Si–Ti–Al Filler Alloy. Materials, 19(18), 3990. https://doi.org/10.3390/ma19183990
Vancouver
Wei L, Lv Z, Xu R, Zhao Y, Wang C, Zheng Y, et al. Microstructure and Shear Strength of SiC Joints Brazed with a Si–Ti–Al Filler Alloy. Materials. 2026;19(18):3990. doi:10.3390/ma19183990
BibTeX
@article{Wei2026,
author = {Wei, Lianfeng and Lv, Zhuyue and Xu, Rui and Zhao, Yumin and Wang, Ce and Zheng, Yong and Li, Xuehan},
title = {Microstructure and Shear Strength of SiC Joints Brazed with a Si–Ti–Al Filler Alloy},
journal = {Materials},
year = {2026},
volume = {19},
number = {18},
pages = {3990},
doi = {10.3390/ma19183990}
}
EUVIMED