EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Freeze–Thaw-Induced Deterioration and Failure Mechanisms of Permeable Concrete in Cold Regions

Zirui Guo, Zhongzhi Guan iD, Yongzhen Zhang, Ting Li, Riguang Chi, Yong Sun, Zhiqiang Chen

Materials · 11.09.2026 · 19 (18) · 3880

DOI: 10.3390/ma19183880 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 11.09.2026. Verfasst von Zirui Guo und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Energy and Architecture Engineering, Harbin University of Commerce, Harbin 150023, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Natural Science Foundation of Heilongjiang Province, Heilongjiang Provincial Environmental Science Research Institute.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To investigate the performance degradation patterns and underlying damage mechanisms of permeable concrete under freeze–thaw cycles in cold regions, permeable concrete with varying porosities was selected as the research subject. A total of 120 rapid low-temperature freeze–thaw cycles were conducted. The evolution of porosity, mass loss, skid resistance, permeability, and compressive strength was systematically analyzed. Exploratory numerical simulations, conducted under idealized assumptions, suggest that rising porosity may reduce effective thermal conductivity, extend phase-change duration, and amplify internal temperature gradients—trends that are consistent with the observed porosity-dependent frost damage but require experimental temperature validation for quantitative confirmation. With the increase in freeze–thaw cycles, mass loss and porosity continuously increase, while compressive strength and permeability gradually decrease. After 120 cycles, the mass loss of all specimen groups was below 1%, with compressive strength decreasing by 5.5% to 12.9%. Despite this, the specimens maintained good permeability and skid resistance. Numerical simulations indicate that permeable concrete exhibits a three-stage temperature response during both freezing and thawing processes. An increase in porosity reduces the material’s effective thermal conductivity, prolongs the phase transition duration, and intensifies the internal temperature gradient, thereby amplifying the thermo–mechanical coupling damage effects. Therefore, optimizing the pore structure is crucial for improving the long-term service performance of permeable pavements in cold regions.

Schlagwörter

Stichwörter der Autor:innen

computational fluid dynamics (CFDs)freeze–thaw cyclespermeable concretephysical and mechanical propertiesporosity

Autor:innen und Institutionen

  • School of Energy and Architecture Engineering, Harbin University of Commerce, Harbin 150023, China.
  • School of Civil Engineering, Heilongjiang University of Science and Technology, Harbin 150022, China.
  • State Key Laboratory of Urban Water Resources and Water Environment, Harbin Institute of Technology, Harbin 150090, China.

ORCID-Profile: Zhongzhi Guan

Förderung

  • the Natural Science Foundation of Heilongjiang Province
  • Heilongjiang Provincial Environmental Science Research Institute

Zitieren

APA

Guo, Z., Guan, Z., Zhang, Y., Li, T., Chi, R., Sun, Y., & Chen, Z. (2026). Freeze–Thaw-Induced Deterioration and Failure Mechanisms of Permeable Concrete in Cold Regions. Materials, 19(18), 3880. https://doi.org/10.3390/ma19183880

Vancouver

Guo Z, Guan Z, Zhang Y, Li T, Chi R, Sun Y, et al. Freeze–Thaw-Induced Deterioration and Failure Mechanisms of Permeable Concrete in Cold Regions. Materials. 2026;19(18):3880. doi:10.3390/ma19183880

BibTeX
@article{Guo2026,
  author = {Guo, Zirui and Guan, Zhongzhi and Zhang, Yongzhen and Li, Ting and Chi, Riguang and Sun, Yong and Chen, Zhiqiang},
  title = {Freeze–Thaw-Induced Deterioration and Failure Mechanisms of Permeable Concrete in Cold Regions},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {18},
  pages = {3880},
  doi = {10.3390/ma19183880}
}
Kostenlos starten →