EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Study on In-Plane Compressive Buckling Behavior and Parameter Optimization of PMMA-Based Thermoplastic Sandwich Structures

Guangtao Li, Xiaofeng Guo, Yifan Wang, Lei Zhou, Jianmin Zhang iD

Materials · 20.08.2026 · 19 (16) · 3525

DOI: 10.3390/ma19163525 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 20.08.2026. Verfasst von Guangtao Li und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Intelligent Mechatronics Engineering, Zhongyuan University of Technology, Zhengzhou 450007, China. Die Arbeit nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Henan Science and Technology Department, Zhongke Technology Achievement Transfer and Transformation Center of Henan Province, Key Specialized Research and Development Projects in Henan Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Thermosetting epoxy resins commonly used in wind turbine blades pose significant recycling challenges. This study addresses this limitation by using an eco-friendly, recyclable liquid polymethyl methacrylate (PMMA) resin to fabricate thermoplastic sandwich panels and by investigating their in-plane compressive buckling behavior. The experimental results demonstrated that the proposed PMMA thermoplastic sandwich panels exhibited improved in-plane compressive performance, with a 5.22% higher ultimate load than traditional epoxy counterparts. Furthermore, to investigate the effect of groove configuration on the buckling stability of composite sandwich panels, a finite element (FE) model for PMMA sandwich panels with initial geometric imperfections was established in this paper, and the reliability of the FE model was validated via compression and buckling tests. Finally, a Kriging surrogate model coupled with the NSGA-II algorithm was adopted to carry out multi-objective optimization, with groove parameters set as design variables. Based on the FE verification results, the optimized configuration (Point A) reduced the structural mass by 2.24%, while increasing the critical buckling load and shear modulus by 5.71% and 10.27%, respectively. Research on the buckling performance and groove configurations of PMMA sandwich panels, which can be applied to wind turbine blade webs and airfoils, can provide crucial data support for the engineering application of sustainable PMMA-based large-scale wind turbine blades.

Schlagwörter

Stichwörter der Autor:innen

groove shapein-plane compressive bucklingmulti-objective optimizationpolymethyl methacrylate (PMMA)sandwich webwind turbine blade

Autor:innen und Institutionen

  • School of Intelligent Mechatronics Engineering, Zhongyuan University of Technology, Zhengzhou 450007, China.
  • Longzihu New Energy Laboratory, Zhengzhou Institute of Emerging Industrial Technology, Zhengzhou 450000, China.
  • Beijing Key Laboratory of Ionic Liquids Clean Process, Institute of Process Engineering, Chinese Academy of Sciences, Beijing 100190, China.

ORCID-Profile: Jianmin Zhang

Förderung

  • Henan Science and Technology Department
  • Zhongke Technology Achievement Transfer and Transformation Center of Henan Province
  • Key Specialized Research and Development Projects in Henan Province

Zitieren

APA

Li, G., Guo, X., Wang, Y., Zhou, L., & Zhang, J. (2026). Study on In-Plane Compressive Buckling Behavior and Parameter Optimization of PMMA-Based Thermoplastic Sandwich Structures. Materials, 19(16), 3525. https://doi.org/10.3390/ma19163525

Vancouver

Li G, Guo X, Wang Y, Zhou L, Zhang J. Study on In-Plane Compressive Buckling Behavior and Parameter Optimization of PMMA-Based Thermoplastic Sandwich Structures. Materials. 2026;19(16):3525. doi:10.3390/ma19163525

BibTeX
@article{Li2026,
  author = {Li, Guangtao and Guo, Xiaofeng and Wang, Yifan and Zhou, Lei and Zhang, Jianmin},
  title = {Study on In-Plane Compressive Buckling Behavior and Parameter Optimization of PMMA-Based Thermoplastic Sandwich Structures},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {16},
  pages = {3525},
  doi = {10.3390/ma19163525}
}
Kostenlos starten →