EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Sequential Topology Optimization and Generative Design with Finite Element Validation for Lightweight PA6 Roller Conveyor Components

Ziad Alamin Emhmed Alhashmi, Aleksandra Mitrovic iD, Marko Tasic, Zorana Golubovic iD, Nenad Mitrovic iD

Materials · 11.08.2026 · 19 (16) · 3401

DOI: 10.3390/ma19163401 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 11.08.2026. Verfasst von Ziad Alamin Emhmed Alhashmi und 4 weiteren Autor:innen. Beteiligte Einrichtung: Faculty for Information technologies and Engineering, University Union-Nikola Tesla, 11000 Belgrade, Serbia. Die Arbeit nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science, Technological Development, and Innovation, Ministry of Science, Technology Development and Innovation of the Republic of Serbia.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Conveyor idler rollers are conventionally manufactured from steel, contributing substantially to the overall mass, energy consumption, and operating cost of belt conveyor systems. A sequential optimization methodology combining topology optimization and generative design is presented to reduce the mass of a polyamide-6 (PA6) idler roller while preserving its structural performance under representative service loading. Starting from a conventional baseline model (1345 g), topology optimization identified low-utilization regions for material removal but introduced an intermediate stiffness penalty, increasing maximum displacement from 3.4 mm to 4.4 mm. Generative design subsequently reorganized the remaining material along the principal load paths, yielding a final component mass of 848 g, a 37% reduction relative to the baseline, while simultaneously reducing maximum displacement to 2.2 mm, a 35% improvement over the original design. The optimized component sustained a maximum von Mises stress of 16.3 MPa under the applied load, corresponding to a safety factor of approximately 3.7 relative to the material’s yield strength. These results, consistent with mass and stiffness improvements reported for generative design applied to comparable load-bearing components, demonstrate that sequential topology optimization and generative design can recover and exceed the stiffness of a conventional design while substantially reducing mass, offering a reproducible pathway toward lighter, more energy-efficient polymer-based conveyor components.

Schlagwörter

Stichwörter der Autor:innen

conveyor idler rollerfinite element analysisgenerative designlightweight structurespolyamide-6 (PA6)topology optimization

Autor:innen und Institutionen

  • Faculty for Information technologies and Engineering, University Union-Nikola Tesla, 11000 Belgrade, Serbia.
  • Department of Forensic Engineering, Faculty of Forensic Sciences and Engineering, CBRNE Center of Excellence, University of Criminal Investigation and Police Studies, 11000 Belgrade, Serbia.
  • The Academy of Applied Studies Polytechnic, 11000 Belgrade, Serbia.
  • University of Belgrade, Faculty of Mechanical Engineering, 11000 Belgrade, Serbia.

ORCID-Profile: Aleksandra Mitrovic, Zorana Golubovic, Nenad Mitrovic

Förderung

  • Ministry of Science, Technological Development, and Innovation
  • Ministry of Science, Technology Development and Innovation of the Republic of Serbia

Zitieren

APA

Alhashmi, Z. A. E., Mitrovic, A., Tasic, M., Golubovic, Z., & Mitrovic, N. (2026). Sequential Topology Optimization and Generative Design with Finite Element Validation for Lightweight PA6 Roller Conveyor Components. Materials, 19(16), 3401. https://doi.org/10.3390/ma19163401

Vancouver

Alhashmi ZAE, Mitrovic A, Tasic M, Golubovic Z, Mitrovic N. Sequential Topology Optimization and Generative Design with Finite Element Validation for Lightweight PA6 Roller Conveyor Components. Materials. 2026;19(16):3401. doi:10.3390/ma19163401

BibTeX
@article{Alhashmi2026,
  author = {Alhashmi, Ziad Alamin Emhmed and Mitrovic, Aleksandra and Tasic, Marko and Golubovic, Zorana and Mitrovic, Nenad},
  title = {Sequential Topology Optimization and Generative Design with Finite Element Validation for Lightweight PA6 Roller Conveyor Components},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {16},
  pages = {3401},
  doi = {10.3390/ma19163401}
}
Kostenlos starten →