EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Study on Electro-Assisted Forming of Thin-Walled Skin Components Made of Ti-6Al-4V Alloy

Zhengang Yuan, Xuefeng Xu, Jiaqi Huang, Jun Xie, Fengwei Zhang, Kai Tian

Materials · 06.08.2026 · 19 (15) · 3352

DOI: 10.3390/ma19153352 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 06.08.2026. Verfasst von Zhengang Yuan und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical and Electrical Engineering, Nanchang Hangkong University, Nanchang 330063, China. Die Arbeit nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Jiangxi Province, National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology of Nanchang Hangkong University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To address the challenges of procedural complexity, the lack of an integrated heating–forming capability, and poor formability in the hot forming of titanium alloy skin components, an electrically assisted forming (EAF) process is proposed. A Johnson–Cook constitutive model was established to characterize the flow behavior of Ti–6Al–4V alloy under electric-assisted conditions, achieving a correlation coefficient of 0.968 and an average relative error of 7.67%. Forming parameters were investigated through a combined approach of numerical simulation and experimentation. At a current density of 7.59 A/mm2, a forming speed of 1 mm/min, and a friction coefficient of 0.1, the maximum springback of the component was 1.04 mm. Compared with isothermal forming, the EAF process reduced the springback by 7.14% and enhanced the ultimate tensile strength by 5.34%. Microstructural characterization revealed that, under pulsed current, the α-phase grains of the material were refined, whereas the β-phase fraction and the average grain size increased, accompanied by a 15.3% reduction in the geometrically necessary dislocation (GND) density. This study validates the process feasibility of electrically assisted forming for thin-walled titanium alloy skin components.

Schlagwörter

Stichwörter der Autor:innen

Ti-6Al-4V alloyconstitutive modelelectrically assisted formingmicrostructure

Autor:innen und Institutionen

  • School of Mechanical and Electrical Engineering, Nanchang Hangkong University, Nanchang 330063, China.
  • Shaanxi Aircraft Industry Co., Ltd., Hanzhong 723200, China.

Förderung

  • National Natural Science Foundation of China
  • Natural Science Foundation of Jiangxi Province
  • National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology of Nanchang Hangkong University
  • Nanchang Hangkong University

Zitieren

APA

Yuan, Z., Xu, X., Huang, J., Xie, J., Zhang, F., & Tian, K. (2026). A Study on Electro-Assisted Forming of Thin-Walled Skin Components Made of Ti-6Al-4V Alloy. Materials, 19(15), 3352. https://doi.org/10.3390/ma19153352

Vancouver

Yuan Z, Xu X, Huang J, Xie J, Zhang F, Tian K. A Study on Electro-Assisted Forming of Thin-Walled Skin Components Made of Ti-6Al-4V Alloy. Materials. 2026;19(15):3352. doi:10.3390/ma19153352

BibTeX
@article{Yuan2026,
  author = {Yuan, Zhengang and Xu, Xuefeng and Huang, Jiaqi and Xie, Jun and Zhang, Fengwei and Tian, Kai},
  title = {A Study on Electro-Assisted Forming of Thin-Walled Skin Components Made of Ti-6Al-4V Alloy},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {15},
  pages = {3352},
  doi = {10.3390/ma19153352}
}
Kostenlos starten →