Tailoring Low-Temperature Tempering to Dramatically Enhance Compressive Ductility and Fatigue Contact Wear Resistance in High-Carbon Bearing Steel
Materials · 06.08.2026 · 19 (15) · 3343
DOI: 10.3390/ma19153343 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 06.08.2026. Verfasst von Hui Li und 7 weiteren Autor:innen. Beteiligte Einrichtung: Shanghai, TianDi Mining Equipment Technology Co., Ltd., Shanghai 200030, China. Die Arbeit nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Special Project for Science and Technology Innovation of China Coal Technology and Engineering Group, Fundamental Research Funds for the Central Universities, National Natural Science Foundation of China.
Abstract (Originalsprache)
High-carbon martensitic steels for bearing components are conventionally low-temperature tempered for stress relief, yet the influence of tempering temperature on compressive and fatigue wear resistance remains unclear, directly affecting the service life of bearing races and rollers. In this study, a high-carbon martensitic steel was tempered at 170 °C, 200 °C, and 230 °C. The microstructural evolution, compressive properties, and contact fatigue wear resistance were systematically investigated, along with the corresponding strengthening and wear mechanisms. After spheroidizing annealing and quenching, the microstructure consists of high-carbon martensite and retained austenite, with a high density of dislocations and fine twins. Tempering decomposes retained austenite into tempered martensite and promotes fine carbide precipitation, processes that become more pronounced at higher temperatures. Consequently, hardness decreases from 810 HV in the as-quenched state to 690 HV after 230 °C tempering, while compressive failure strain increases from 10.5% to 24.1%. More importantly, under cyclic contact stress, the 230 °C-tempered specimen exhibits approximately 33% lower wear mass loss than the 170 °C-tempered counterpart, despite its lower hardness. This unexpected improvement is attributed to the formation of a distinct plastic deformation zone in the near-surface region, which absorbs greater strain energy and delays fatigue spallation. The well-tempered martensitic matrix accommodates more long-range dislocation slip, enabling a transition from fatigue spallation to a more ductile failure mode. These findings provide new insights into the role of low-temperature tempering in balancing strength, ductility, and wear resistance, and offer practical guidance for optimizing heat treatment protocols to enhance the contact fatigue performance of bearing steels.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Shanghai, TianDi Mining Equipment Technology Co., Ltd., Shanghai 200030, China.
- School of Mechanical and Electrical Engineering, China University of Mining and Technology, Xuzhou 221116, China.
- State Key Laboratory of Intelligent Mining Equipment Technology, China University of Mining and Technology, Xuzhou 221116, China.
Förderung
- Special Project for Science and Technology Innovation of China Coal Technology and Engineering Group
- Fundamental Research Funds for the Central Universities
- National Natural Science Foundation of China
Zitieren
APA
Li, H., Song, X., Tao, Q., Wang, Z., Huang, Q., Xu, W., Li, Q., & Wang, J. (2026). Tailoring Low-Temperature Tempering to Dramatically Enhance Compressive Ductility and Fatigue Contact Wear Resistance in High-Carbon Bearing Steel. Materials, 19(15), 3343. https://doi.org/10.3390/ma19153343
Vancouver
Li H, Song X, Tao Q, Wang Z, Huang Q, Xu W, et al. Tailoring Low-Temperature Tempering to Dramatically Enhance Compressive Ductility and Fatigue Contact Wear Resistance in High-Carbon Bearing Steel. Materials. 2026;19(15):3343. doi:10.3390/ma19153343
BibTeX
@article{Li2026,
author = {Li, Hui and Song, Xiangkun and Tao, Qing and Wang, Zhenqian and Huang, Qiulai and Xu, Weipeng and Li, Qingliang and Wang, Jian},
title = {Tailoring Low-Temperature Tempering to Dramatically Enhance Compressive Ductility and Fatigue Contact Wear Resistance in High-Carbon Bearing Steel},
journal = {Materials},
year = {2026},
volume = {19},
number = {15},
pages = {3343},
doi = {10.3390/ma19153343}
}
EUVIMED