EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Flocculation Characteristics and Dewatering Performance of Bored Pile Waste Slurry with Different Flocculants

Shouju Miao, Jun Chen, Zhihai Zhang, Shuirong Gui, Ling Zhou, Shengjie Liu

Materials · 04.08.2026 · 19 (15) · 3299

DOI: 10.3390/ma19153299 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 04.08.2026. Verfasst von Shouju Miao und 5 weiteren Autor:innen. Beteiligte Einrichtung: Jiangxi Provincial Communications Investment Group Co., Ltd., Nanchang 330000, China. Die Arbeit nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science and Technology Project of Jiangxi Provincial Department of Transportation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Bored pile waste slurry generated during bridge substructure construction exhibits high water content and stable colloidal properties, resulting in difficult solid–liquid separation and severe environmental risks. To improve solid–liquid separation and facilitate efficient disposal, this study systematically investigated the flocculation and dewatering performance of the slurry using three typical flocculants (Anionic polyacrylamide (APAM), cationic polyacrylamide (CPAM), and polymeric aluminum chloride(PAC)) through sedimentation tests, supernatant purification monitoring, particle size analysis, zeta potential measurements, and specific filtration resistance tests. The results show that flocculant type and dosage significantly affect treatment efficiency. Organic flocculants outperform inorganic PAC in both particle aggregation and dewatering improvement. Among them, APAM exhibits a prominent low-dose advantage; at an optimal dosage of 0.2–0.3% (corresponding to a pure reagent dosage of 10–15 mg/L based on wet slurry), it effectively reduces the slurry water content and lowers supernatant suspended solids below the 50 mg/L discharge standard within 80 min. Mechanistically, PAC provides primarily electrostatic neutralization, whereas APAM and CPAM achieve composite flocculation through charge neutralization, adsorption bridging, and sweep capture. Benefiting from efficient low-dose neutralization and long-chain bridging effects, APAM significantly reduces filtration resistance and forms stable flocs. Overall, an APAM dosage of 10–15 mg/L is the optimal scheme for in situ treatment of bored pile waste slurry, providing technical support for the efficient management and controlled disposal of engineering slurry under similar geological conditions.

Schlagwörter

Stichwörter der Autor:innen

bored pile waste slurrydewatering performanceflocculation lawsolid–liquid separationspecific filtration resistancezeta potential

Autor:innen und Institutionen

  • Jiangxi Provincial Communications Investment Group Co., Ltd., Nanchang 330000, China.
  • Jiangxi Provincial Highway and Bridge Engineering Co., Ltd., Nanchang 330008, China.
  • School of Civil Engineering and Architecture, East China Jiaotong University, Nanchang 330013, China.
  • College of Civil and Transportation Engineering, Hohai University, Nanjing 210098, China.

Förderung

  • Science and Technology Project of Jiangxi Provincial Department of Transportation

Zitieren

APA

Miao, S., Chen, J., Zhang, Z., Gui, S., Zhou, L., & Liu, S. (2026). Flocculation Characteristics and Dewatering Performance of Bored Pile Waste Slurry with Different Flocculants. Materials, 19(15), 3299. https://doi.org/10.3390/ma19153299

Vancouver

Miao S, Chen J, Zhang Z, Gui S, Zhou L, Liu S. Flocculation Characteristics and Dewatering Performance of Bored Pile Waste Slurry with Different Flocculants. Materials. 2026;19(15):3299. doi:10.3390/ma19153299

BibTeX
@article{Miao2026,
  author = {Miao, Shouju and Chen, Jun and Zhang, Zhihai and Gui, Shuirong and Zhou, Ling and Liu, Shengjie},
  title = {Flocculation Characteristics and Dewatering Performance of Bored Pile Waste Slurry with Different Flocculants},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {15},
  pages = {3299},
  doi = {10.3390/ma19153299}
}
Kostenlos starten →