EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Springback Behavior and Stroke-Based Compensation Strategy for Roll-Based Bending of High-Strength Aluminum Extrusions

Jeongsik Lim, Hyungjun Kim iD, Jinho Kim iD, Hoyoung Kang, Changhwan Seo, Haeyong Yun

Materials · 03.08.2026 · 19 (15) · 3275

DOI: 10.3390/ma19153275 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 03.08.2026. Verfasst von Jeongsik Lim und 5 weiteren Autor:innen. Beteiligte Einrichtung: Gyeongbuk Technopark, 120 Gongdan 7-ro, Jillyang-eup, Gyeongsan 38463, Republic of Korea. Die Arbeit nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Trade, Industry & Resources (MOTIR, Korea).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

High-strength aluminum tubular extrusions are being increasingly used in lightweight automotive structures; however, the significant springback caused by elastic recovery after bending compromises geometric accuracy. In roll-based bending processes, springback behavior is affected by multiple process parameters, which necessitates a systematic investigation and a simulation-based springback compensation approach. In this study, the springback behavior of high-strength aluminum tubular extrusions subjected to roll-based bending was investigated via finite-element analysis. The effects of feeding displacement, roller rotational speed, and internal mandrel application on springback were comparatively evaluated. Springback was quantitatively assessed based on the displacement and angular deviation after unloading, and the influence of each process parameter was analyzed. Based on the results, variations in roller rotational speed had a negligible effect on springback, whereas feeding displacement was identified as the dominant governing factor under all investigated conditions. Although internal mandrel application reduced stress levels and mitigated wrinkle formation, the overall springback tendency remained dependent on feeding displacement. Based on these findings, a simulation-based stroke compensation approach was proposed, and a compensation window satisfying the target curvature radius of R = 150 mm was numerically identified under the investigated finite-element conditions.

Schlagwörter

Stichwörter der Autor:innen

feeding displacementhigh-strength aluminum extrusionroll-based bendingspringback behaviorstroke-based compensation

Autor:innen und Institutionen

  • Gyeongbuk Technopark, 120 Gongdan 7-ro, Jillyang-eup, Gyeongsan 38463, Republic of Korea.
  • Department of Mechanical Engineering, Yeungnam University, Gyeongsan 38541, Republic of Korea.
  • R&D Center, ALUS Co., Ltd., 76 Yeongudanji-ro, Ochang-eup, Cheongju 28116, Republic of Korea.
  • Korea Institute of Robotics & Technology Convergence, 1486-20 Gyeongdong-ro, Andong 36728, Republic of Korea.

ORCID-Profile: Hyungjun Kim, Jinho Kim

Förderung

  • Ministry of Trade, Industry & Resources (MOTIR, Korea)

Zitieren

APA

Lim, J., Kim, H., Kim, J., Kang, H., Seo, C., & Yun, H. (2026). Springback Behavior and Stroke-Based Compensation Strategy for Roll-Based Bending of High-Strength Aluminum Extrusions. Materials, 19(15), 3275. https://doi.org/10.3390/ma19153275

Vancouver

Lim J, Kim H, Kim J, Kang H, Seo C, Yun H. Springback Behavior and Stroke-Based Compensation Strategy for Roll-Based Bending of High-Strength Aluminum Extrusions. Materials. 2026;19(15):3275. doi:10.3390/ma19153275

BibTeX
@article{Lim2026,
  author = {Lim, Jeongsik and Kim, Hyungjun and Kim, Jinho and Kang, Hoyoung and Seo, Changhwan and Yun, Haeyong},
  title = {Springback Behavior and Stroke-Based Compensation Strategy for Roll-Based Bending of High-Strength Aluminum Extrusions},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {15},
  pages = {3275},
  doi = {10.3390/ma19153275}
}
Kostenlos starten →