EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Scandium Microalloying for Al-Cu-Mg-Mn-Ti Alloys with High Cu Content

Junbao Guo, Hao Dong, Yuan Wang, Yuqian Wang, Zhenjie Zhao, Ruihong Zhang, Zekang Li, Yanfeng Liang, Zhong Yang

Materials · 18.07.2026 · 19 (14) · 3095

DOI: 10.3390/ma19143095 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.07.2026. Verfasst von Junbao Guo und 8 weiteren Autor:innen. Beteiligte Einrichtung: School of Materials and Chemical Engineering, Xi'an Technological University, Xi'an 710021, China. Die Arbeit nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Increasing the Cu content is an important approach to enhancing the strength of Al-Cu alloys, but the widening of the solidification temperature range leads to deterioration in the casting performance of the alloy, significantly limiting its application. This work investigates the effect of Sc content on the microstructure and mechanical properties of Al-Cu-Mg-Mn-Ti alloys with high Cu content. The results show that the solidification path of the Al-8.5Cu-0.3Mg-0.35Mn-0.2Ti-xSc alloy changes when the Sc content reaches 0.37%. When the Sc content is less than 0.37%, the primary phase is α-Al, whereas when the Sc content is greater than 0.37%, the primary phase is Al3Sc. As the Sc content increases to 0.4%, the grain size of the alloy first decreases and then increases, with the smallest grain size occurring at a Sc addition of 0.3 wt.%. Accordingly, the tensile strength of the alloy at both room temperature and high temperature reaches the highest when the Sc content is 0.3 wt.%. Specifically, the alloy’s tensile strength at room temperature reaches 327.2 MPa, an increase of 14.0% compared to the alloy without Sc, and the alloy’s tensile strength reaches 103 MPa at 350 °C, an increase of 24.5% compared to the alloy without Sc. It is speculated that when Sc is added to the Al-Cu melt, it refines the grains by forming Al3Sc heterogeneous nucleation cores, and it may also form Sc-containing precipitates with higher temperature resistance, which boosts the alloy’s strength.

Schlagwörter

Stichwörter der Autor:innen

Al-Cu alloySc elementgrain refinementmechanical propertymicrostructure

Autor:innen und Institutionen

  • School of Materials and Chemical Engineering, Xi'an Technological University, Xi'an 710021, China.
  • Shanxi Diesel Engine Industry Co. Ltd., Datong 037001, China.
  • Engineering Training Center, Xi'an Technological University, Xi'an 710021, China.

Zitieren

APA

Guo, J., Dong, H., Wang, Y., Wang, Y., Zhao, Z., Zhang, R., Li, Z., Liang, Y., & Yang, Z. (2026). Scandium Microalloying for Al-Cu-Mg-Mn-Ti Alloys with High Cu Content. Materials, 19(14), 3095. https://doi.org/10.3390/ma19143095

Vancouver

Guo J, Dong H, Wang Y, Wang Y, Zhao Z, Zhang R, et al. Scandium Microalloying for Al-Cu-Mg-Mn-Ti Alloys with High Cu Content. Materials. 2026;19(14):3095. doi:10.3390/ma19143095

BibTeX
@article{Guo2026,
  author = {Guo, Junbao and Dong, Hao and Wang, Yuan and Wang, Yuqian and Zhao, Zhenjie and Zhang, Ruihong and Li, Zekang and Liang, Yanfeng and Yang, Zhong},
  title = {Scandium Microalloying for Al-Cu-Mg-Mn-Ti Alloys with High Cu Content},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {14},
  pages = {3095},
  doi = {10.3390/ma19143095}
}
Kostenlos starten →