EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure, Mechanical Response, and Tribological Behavior of Mechanically Alloyed and Microwave-Sintered AA7068/TiB2–TiC Hybrid Composites

Emre Özer iD

Materials · 16.07.2026 · 19 (14) · 3072

DOI: 10.3390/ma19143072 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 16.07.2026. Verfasst von Emre Özer. Beteiligte Einrichtung: Department of Industrial Engineering, Osmaniye Korkut Ata University, Osmaniye 80000, Turkey. Die Arbeit nennt 89 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, AA7068 aluminum matrix composites reinforced with TiB2/TiC were fabricated via mechanical alloying and microwave sintering to investigate the influence of reinforcement content and sintering temperature on microstructure, mechanical properties, and dry sliding wear. Mechanical alloying refined powders, reducing D50 from 51.5 µm (AA) to 22.5 µm (AC9) and enhancing dispersion and retention of TiB2/TiC particles. XRD confirmed α-Al as the dominant matrix phase, preserved TiB2 and TiC phases, and limited MgAl2O4/ZnAl2O4 spinel formation. Crystallite refinement and increased lattice microstrain were observed with the addition of reinforcement. Microhardness increased with reinforcement content and sintering temperature, reaching 122.2 HV0.05 in AC9-2. At the same time, the highest compressive strength was observed in AC6-2 (431.05 MPa), indicating that optimal load-bearing depends on densification and interfacial integrity rather than hardness alone. AC9-2 exhibited the best wear resistance, with a cumulative specific wear rate of 2.723 × 10−4 mm3/Nm over 1000 m. SEM-EDS analysis revealed oxide-rich tribolayers, mechanically mixed layers, TiB2/TiC fragments, and Fe-rich third-body debris, indicating wear is predominantly hardness-controlled but strongly influenced by microstructural factors. Overall, TiB2/TiC hybrid reinforcement improves AA7068 wear resistance through combined hard-particle load-bearing, reduced penetration, tribolayer stability, and third-body effects, offering insight for high-performance hybrid aluminum composites.

Schlagwörter

Stichwörter der Autor:innen

7068 aluminum alloyTiB2–TiChybrid compositesmechanical propertiespowder metallurgywear

Autor:innen und Institutionen

  • Department of Industrial Engineering, Osmaniye Korkut Ata University, Osmaniye 80000, Turkey.

ORCID-Profile: Emre Özer

Zitieren

APA

Özer, E. (2026). Microstructure, Mechanical Response, and Tribological Behavior of Mechanically Alloyed and Microwave-Sintered AA7068/TiB2–TiC Hybrid Composites. Materials, 19(14), 3072. https://doi.org/10.3390/ma19143072

Vancouver

Özer E. Microstructure, Mechanical Response, and Tribological Behavior of Mechanically Alloyed and Microwave-Sintered AA7068/TiB2–TiC Hybrid Composites. Materials. 2026;19(14):3072. doi:10.3390/ma19143072

BibTeX
@article{zer2026,
  author = {Özer, Emre},
  title = {Microstructure, Mechanical Response, and Tribological Behavior of Mechanically Alloyed and Microwave-Sintered AA7068/TiB2–TiC Hybrid Composites},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {14},
  pages = {3072},
  doi = {10.3390/ma19143072}
}
Kostenlos starten →