EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Barrier-Oriented FWGM-Based Fuzzy-FMEA for Risk Assessment and Safety-Barrier Prioritization in Solvent-Based Electrospinning Processes

Jong Gu Kim iD, Byong Chol Bai iD

Materials · 22.06.2026 · 19 (12) · 2673

DOI: 10.3390/ma19122673 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 22.06.2026. Verfasst von Jong Gu Kim und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Fire and Disaster Prevention and Safety, Sun Moon University, Asan 31460, Republic of Korea. Die Arbeit nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Sun Moon University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study proposes a barrier-oriented application of conventional failure mode and effects analysis (FMEA) and fuzzy weighted geometric mean (FWGM)-based fuzzy-FMEA for laboratory-scale solvent-based electrospinning. The process was decomposed into 14 sequential steps, and one representative failure mode was defined for each step. Severity, occurrence, and detection were rated by a five-member expert panel, and hazard-type-specific weights were assigned to chemical-dominant, electrical-dominant, fire/static-dominant, and combined-dominant hazards. Conventional FMEA identified material review/approval, equipment setup, pre-start inspection, and response to abnormalities as the highest-risk steps (RPN = 60). FWGM-based fuzzy-FMEA re-ranked tied RPN groups and identified response to abnormalities and equipment setup as the joint highest-FRPN failure modes (FRPN = 79.35), followed by pre-start inspection (77.39) and material review/approval (75.89). Barrier-oriented interpretation revealed four dominant mechanisms: upstream information-based hazards, direct high-voltage access, pre-start combined hazards, and intervention under abnormal or residual-energy states. Scenario-based post-control analysis showed that grounded enclosures, interlocks, de-energize-discharge-verify procedures, pre-start checklists, and bonding/grounding measures reduced FRPN by 25.88–43.79% for prioritized failure modes. The proposed framework supports SOP development, equipment improvement, training prioritization, and laboratory risk-assessment documentation for solvent-based nanofiber manufacturing.

Schlagwörter

Stichwörter der Autor:innen

electrospinningfuzzy-FMEAnanofiber manufacturingprocess safetysafety barriers

Autor:innen und Institutionen

  • Department of Fire and Disaster Prevention and Safety, Sun Moon University, Asan 31460, Republic of Korea.
  • Department of Chemical Engineering, Daejin University, Pocheon 11159, Republic of Korea.

ORCID-Profile: Jong Gu Kim, Byong Chol Bai

Förderung

  • Sun Moon University

Zitieren

APA

Kim, J. G., & Bai, B. C. (2026). Barrier-Oriented FWGM-Based Fuzzy-FMEA for Risk Assessment and Safety-Barrier Prioritization in Solvent-Based Electrospinning Processes. Materials, 19(12), 2673. https://doi.org/10.3390/ma19122673

Vancouver

Kim JG, Bai BC. Barrier-Oriented FWGM-Based Fuzzy-FMEA for Risk Assessment and Safety-Barrier Prioritization in Solvent-Based Electrospinning Processes. Materials. 2026;19(12):2673. doi:10.3390/ma19122673

BibTeX
@article{Kim2026,
  author = {Kim, Jong Gu and Bai, Byong Chol},
  title = {Barrier-Oriented FWGM-Based Fuzzy-FMEA for Risk Assessment and Safety-Barrier Prioritization in Solvent-Based Electrospinning Processes},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {12},
  pages = {2673},
  doi = {10.3390/ma19122673}
}
Kostenlos starten →