EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative Evaluation of Mechanical Behaviour and Machinability of WAAM-Fabricated Aluminium Alloys

Saravanamurugan Sundaram iD, Thenarasu Mohanavelu iD, Sumesh Arangot iD, Jana Petru iD, Mohan Ruthramoorthy, Rashaad Sabir Rowther, Kamalesh Senthilkumar

Materials · 20.06.2026 · 19 (12) · 2653

DOI: 10.3390/ma19122653 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 20.06.2026. Verfasst von Saravanamurugan Sundaram und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore 641112, India. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study presents an integrated evaluation of the mechanical properties and machinability of thin-walled aluminium alloys fabricated via Wire Arc Additive Manufacturing (WAAM), comparing them against conventional wrought counterparts. Experimental investigations were conducted through tensile testing, hardness measurement, surface characterisation, and cutting force analysis. The results reveal a critical performance trade-off: WAAM specimens demonstrated superior bulk mechanical properties, most notably a 44.36% increase in tensile strength, alongside enhanced elongation despite a marginal reduction in hardness. However, this structural advantage is counterbalanced by a significant machinability penalty. Frequency domain analysis using Power Spectral Density (PSD) revealed that inherent microstructural porosity in WAAM components triggers dynamic instabilities during machining. These irregularities make the material highly susceptible to high-frequency chatter, ultimately resulting in a 46.73% increase in surface roughness. By establishing a direct relationship between fabrication-induced microstructural defects and dynamic machining degradation, these findings emphasise the necessity for defect-aware, optimised hybrid manufacturing strategies to improve the industrial applicability of WAAM-fabricated structures.

Schlagwörter

Stichwörter der Autor:innen

Wire Arc Additive Manufacturing (WAAM)chattermachinabilityporositypower spectral densitythin-walled aluminium alloy

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore 641112, India.
  • Department of Machining, Assembly and Engineering Metrology, Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 70800 Ostrava, Czech Republic.

ORCID-Profile: Saravanamurugan Sundaram, Thenarasu Mohanavelu, Sumesh Arangot, Jana Petru

Förderung

  • European Union

Zitieren

APA

Sundaram, S., Mohanavelu, T., Arangot, S., Petru, J., Ruthramoorthy, M., Rowther, R. S., & Senthilkumar, K. (2026). Comparative Evaluation of Mechanical Behaviour and Machinability of WAAM-Fabricated Aluminium Alloys. Materials, 19(12), 2653. https://doi.org/10.3390/ma19122653

Vancouver

Sundaram S, Mohanavelu T, Arangot S, Petru J, Ruthramoorthy M, Rowther RS, et al. Comparative Evaluation of Mechanical Behaviour and Machinability of WAAM-Fabricated Aluminium Alloys. Materials. 2026;19(12):2653. doi:10.3390/ma19122653

BibTeX
@article{Sundaram2026,
  author = {Sundaram, Saravanamurugan and Mohanavelu, Thenarasu and Arangot, Sumesh and Petru, Jana and Ruthramoorthy, Mohan and Rowther, Rashaad Sabir and Senthilkumar, Kamalesh},
  title = {Comparative Evaluation of Mechanical Behaviour and Machinability of WAAM-Fabricated Aluminium Alloys},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {12},
  pages = {2653},
  doi = {10.3390/ma19122653}
}
Kostenlos starten →