EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Unraveling the Distinct Roles of Al and Ca in Microstructure Evolution and Tensile Response of Extruded Mg–Al–Ca Alloys

Chen Chen, Junbo Wang, Yong Wang, Changyu Hu, Shengxiong Tang, Ranfeng Qiu iD, Yiwen Chen iD

Materials · 18.06.2026 · 19 (12) · 2638

DOI: 10.3390/ma19122638 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 18.06.2026. Verfasst von Chen Chen und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Intelligent Manufacturing, Jiangnan University, Wuxi 214122, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Basic Research Program of Jiangsu, Wuxi Science and Technology Development Fund Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Mg-Al-Ca alloys are attractive low-cost wrought Mg alloys. However, the distinct roles of Al and Ca in regulating deformation-processed microstructures and mechanical properties remain unclear. In this work, Mg–6Al–0.5Ca, Mg–9Al–0.5Ca, and Mg–9Al–1.3Ca (wt. %) alloys were extruded at 250 °C and 300 °C to clarify the composition-dependent microstructure evolution and strengthening mechanisms. Increasing the Al content from 6 to 9 wt. % markedly promoted the formation of fine Mg17Al12 (f-Mg17Al12) and coarse Mg17Al12 particles, whereas increasing the Ca content from 0.5 to 1.3 wt. % promoted the formation of coarse Al2Ca particles while reducing the density of f-Mg17Al12. Quantitative analysis revealed that f-Mg17Al12 particles refined dynamically recrystallized grains by promoting recrystallization nucleation and pinning grain boundaries while also contributing to Orowan strengthening. The Mg–9Al–0.5Ca alloy exhibited the best strength–ductility balance, with a yield strength of 338 ± 4 MPa, ultimate tensile strength of 396 ± 5 MPa, and elongation of 8.7 ± 1.6% after extrusion at 250 °C. Strengthening calculations indicated that grain-boundary strengthening was the dominant strengthening contribution, while the strength advantage of Mg–9Al–0.5Ca originated from the dual role of f-Mg17Al12 in grain refinement and dislocation obstruction. These findings provide a practical strategy for designing high-strength non-rare-earth Mg–Al–Ca extrusion alloys.

Schlagwörter

Stichwörter der Autor:innen

Mg–Al–Ca alloyOrowan strengtheningfine Mg17Al12 particlesgrain refinementmechanical properties

Autor:innen und Institutionen

  • School of Intelligent Manufacturing, Jiangnan University, Wuxi 214122, China.
  • School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China.
  • Department of Materials Science, Graduate School of Science and Technology, Kumamoto University, 2-39-1 Kurokami, Chuo-ku, Kumamoto 860-8555, Japan.
  • School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471039, China.

ORCID-Profile: Ranfeng Qiu, Yiwen Chen

Förderung

  • National Natural Science Foundation of China
  • Basic Research Program of Jiangsu
  • Wuxi Science and Technology Development Fund Project
  • Fundamental Research Funds for the Central Universities

Zitieren

APA

Chen, C., Wang, J., Wang, Y., Hu, C., Tang, S., Qiu, R., & Chen, Y. (2026). Unraveling the Distinct Roles of Al and Ca in Microstructure Evolution and Tensile Response of Extruded Mg–Al–Ca Alloys. Materials, 19(12), 2638. https://doi.org/10.3390/ma19122638

Vancouver

Chen C, Wang J, Wang Y, Hu C, Tang S, Qiu R, et al. Unraveling the Distinct Roles of Al and Ca in Microstructure Evolution and Tensile Response of Extruded Mg–Al–Ca Alloys. Materials. 2026;19(12):2638. doi:10.3390/ma19122638

BibTeX
@article{Chen2026,
  author = {Chen, Chen and Wang, Junbo and Wang, Yong and Hu, Changyu and Tang, Shengxiong and Qiu, Ranfeng and Chen, Yiwen},
  title = {Unraveling the Distinct Roles of Al and Ca in Microstructure Evolution and Tensile Response of Extruded Mg–Al–Ca Alloys},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {12},
  pages = {2638},
  doi = {10.3390/ma19122638}
}
Kostenlos starten →