Effect of SiC Content on Microstructure and Mechanical Properties of CoCrFeNi High-Entropy Alloy Composites
Materials · 10.06.2026 · 19 (12) · 2501
DOI: 10.3390/ma19122501 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 10.06.2026. Verfasst von Ning Li und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Materials Science and Engineering, North Minzu University, Yinchuan 750021, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: North Minzu University, Ningxia Natural Science Foundation, Fundamental Research Funds for the Central Universities, North Minzu University.
Abstract (Originalsprache)
In this work, to address the limitation of low strength and hardness of single-phase CoCrFeNi high-entropy alloy, SiC particles were introduced as a reinforcing phase to prepare CoCrFeNi matrix composites with SiC contents of 0 wt%, 1 wt%, 2.5 wt% and 5 wt% via spark plasma sintering (SPS). It was preliminarily predicted that SiC particles would be uniformly distributed along grain boundaries of the CoCrFeNi matrix. During sintering, partial SiC decomposes at high-temperature, high-activity interfaces, regulating carbide precipitation and phase structural evolution, while residual undecomposed SiC remains at grain boundaries to pin boundaries and refine grains, thereby synergistically enhancing mechanical properties and wear resistance. Microstructural characterization reveals that all samples maintain a face-centered cubic (FCC) solid-solution matrix, and samples with non-zero SiC addition contain Cr7C3 carbides, which are mostly distributed at grain boundaries. With the increase in SiC content, mechanical performance is remarkably improved compared with the unreinforced CoCrFeNi matrix: the hardness rises from 198.8 HV to 321.7 HV, the yield strength is greatly enhanced from 242.5 MPa to 673.4 MPa, and the tensile strength increases from 557.9 MPa to 755.7 MPa. The improved yield strength originates synergistically from grain refinement, solid-solution strengthening, grain-boundary strengthening and dislocation strengthening. By clarifying the influence of microstructural defects on critical shear stress (τ0) and normal fracture stress (σ0), the intrinsic mechanism governing tensile mechanical performance and ductile–brittle fracture transition was revealed. This optimized CoCrFeNi/SiC composite exhibits excellent strength–hardness comprehensive performance, showing promising application potential for high-load, wear-resistant and structural service components under severe tribological and pressure conditions.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Materials Science and Engineering, North Minzu University, Yinchuan 750021, China.
- National and Local Joint Engineering Research Center of Advanced Carbon-Based Ceramics Preparation Technology, Yinchuan 750021, China.
- Key Laboratory of Powder Materials & Advanced Ceramics, Yinchuan 750021, China.
ORCID-Profile: Chengbo Wu, Fuyuan Dong
Förderung
- North Minzu University
- Ningxia Natural Science Foundation
- Fundamental Research Funds for the Central Universities, North Minzu University
Zitieren
APA
Li, N., Hu, X., Wu, C., Jiang, M., Li, H., Zhang, J., & Dong, F. (2026). Effect of SiC Content on Microstructure and Mechanical Properties of CoCrFeNi High-Entropy Alloy Composites. Materials, 19(12), 2501. https://doi.org/10.3390/ma19122501
Vancouver
Li N, Hu X, Wu C, Jiang M, Li H, Zhang J, et al. Effect of SiC Content on Microstructure and Mechanical Properties of CoCrFeNi High-Entropy Alloy Composites. Materials. 2026;19(12):2501. doi:10.3390/ma19122501
BibTeX
@article{Li2026,
author = {Li, Ning and Hu, Xinlong and Wu, Chengbo and Jiang, Mengyuan and Li, Huiying and Zhang, Jinlong and Dong, Fuyuan},
title = {Effect of SiC Content on Microstructure and Mechanical Properties of CoCrFeNi High-Entropy Alloy Composites},
journal = {Materials},
year = {2026},
volume = {19},
number = {12},
pages = {2501},
doi = {10.3390/ma19122501}
}
EUVIMED