EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Experimental Investigation and Predictive Modeling of Cumulative Plastic Deformation of Silty Sand Under Freeze–Thaw Cycles and Cyclic Loading

Dongkai Ma, Zhongming He, Yiwei Li, Zhenhong Yan, Chao Huang

Materials · 09.06.2026 · 19 (12) · 2461

DOI: 10.3390/ma19122461 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 09.06.2026. Verfasst von Dongkai Ma und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Traffic and Transportation on Engineering, Changsha University of Science & Technology, Changsha 410004, China. Die Arbeit nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Department of Science and Technology of Hunan Province, Natural Science Foundation of Hunan Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The long-term deformation and stability of silty sand roadbeds subjected to repeated freeze–thaw cycles and traffic loading remain ongoing engineering concerns in seasonally frozen regions. To investigate the evolution and influencing factors of accumulative axial plastic deformation of silty sand under freeze–thaw cycles, this study focused on silty sand from a roadbed construction site in Inner Mongolia, China, a typical seasonally frozen region. Dynamic triaxial tests were conducted under loading stresses of 60–100 kPa, confining pressures of 20–60 kPa, water contents ranging from OMC to 1.2 OMC, and freeze–thaw cycles of 0–10. The results indicate that approximately 60–80% of the total accumulative axial plastic deformation occurs within the first 1000 loading cycles, after which the deformation growth rate gradually decreases. Increases in loading stress, water content, and freeze–thaw cycles promote deformation, whereas higher confining pressures suppress it. For example, increasing the confining pressure from 20 to 60 kPa reduced the final deformation from 0.16% to 0.07%, while increasing the number of freeze–thaw cycles from 0 to 10 increased the final deformation from 0.10% to 0.28%. Based on the experimental data, a new predictive model considering net stress, octahedral shear stress, water content ratio, and freeze–thaw cycles was developed. The model demonstrates high accuracy in predicting accumulative plastic deformation, with a coefficient of determination of 0.915, and is applicable to both plastically stable and weakly plastic creep conditions. This study provides a reference for the design, construction, and mitigation of subgrade damage in silty sand roadbeds in seasonally frozen regions.

Schlagwörter

Stichwörter der Autor:innen

cumulative plastic deformationfreeze–thaw cyclesprediction modelsilty sand

Autor:innen und Institutionen

  • School of Traffic and Transportation on Engineering, Changsha University of Science & Technology, Changsha 410004, China.
  • National Engineering Research Center of Highway Maintenance Technology, Changsha 410004, China.
  • School of Civil Engineering, Central South University, Changsha 410075, China.

Förderung

  • National Natural Science Foundation of China
  • Department of Science and Technology of Hunan Province
  • Natural Science Foundation of Hunan Province

Zitieren

APA

Ma, D., He, Z., Li, Y., Yan, Z., & Huang, C. (2026). Experimental Investigation and Predictive Modeling of Cumulative Plastic Deformation of Silty Sand Under Freeze–Thaw Cycles and Cyclic Loading. Materials, 19(12), 2461. https://doi.org/10.3390/ma19122461

Vancouver

Ma D, He Z, Li Y, Yan Z, Huang C. Experimental Investigation and Predictive Modeling of Cumulative Plastic Deformation of Silty Sand Under Freeze–Thaw Cycles and Cyclic Loading. Materials. 2026;19(12):2461. doi:10.3390/ma19122461

BibTeX
@article{Ma2026,
  author = {Ma, Dongkai and He, Zhongming and Li, Yiwei and Yan, Zhenhong and Huang, Chao},
  title = {Experimental Investigation and Predictive Modeling of Cumulative Plastic Deformation of Silty Sand Under Freeze–Thaw Cycles and Cyclic Loading},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {12},
  pages = {2461},
  doi = {10.3390/ma19122461}
}
Kostenlos starten →