Industrial-Scale Injection Moulding Validation of Recycled Fiber-Reinforced Polypropylene: Processability and Manufacturing Feasibility
Materials · 30.05.2026 · 19 (11) · 2314
DOI: 10.3390/ma19112314 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 30.05.2026. Verfasst von Elena Picazo Camilo und 6 weiteren Autor:innen. Beteiligte Einrichtung: EcoCastulum, Avenida de la Universidad 1, 23700 Linares, Spain. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: INCIRCULAR project.
Abstract (Originalsprache)
This study evaluates the industrial-scale feasibility of injection moulding of a recycled polypropylene composite reinforced with recycled fibers derived from an industrial waste stream. Although previous laboratory-scale research has demonstrated the potential of natural fiber-reinforced thermoplastics, their large-scale industrial implementation remains limited due to uncertainties related to processability, reproducibility, and manufacturing robustness. In this work, the composite material is validated through injection moulding trials carried out in four independent industrial companies located in Andalusia (Spain) and three industrial case studies across different industrial sectors in Slovenia, operating under real production conditions. The extrusion process was characterized in terms of process stability, confirming continuous operation with automated dosing and stable material flow without interruptions under industrial conditions. Injection processing parameters, cycle stability, part quality, and defect formations are also considered important when assessing the manufacturing feasibility. The multi-site validation approach enables the evaluation of reproducibility across different injection moulding systems and mould geometries, providing critical insights into the scalability and technological readiness level of recycled natural fiber-reinforced polypropylene composites. Although direct energy consumption measurements were not systematically recorded, the observed processing stability and cycle repeatability indicate a consistent and energy-efficient operation under industrial processing conditions. The results contribute to bridging the gap between laboratory-scale material development and real industrial implementation.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- EcoCastulum, Avenida de la Universidad 1, 23700 Linares, Spain.
- Department of Chemical, Environmental and Materials Engineering, Higher Polytechnic School of Linares, University of Jaén, Campus Científico-Tecnológico de Linares, 23700 Linares, Spain.
- TECOS, Slovenian Tool and Die Development Centre, Kidričeva Cesta 25, SI-3000 Celje, Slovenia.
- Gorenje Gospodinjski Aparati, Partizanska Cesta 12, SI-3320 Velenje, Slovenia.
ORCID-Profile: Elena Picazo Camilo, Raúl Carrillo Beltrán, Griselda Elisabeth Perea Toledo, Francisco Antonio Corpas Iglesias, Vesna Žepič Bogataj, Simon Kotnik, Francisco Javier Iglesias Godino
Förderung
- INCIRCULAR project
Zitieren
APA
Picazo Camilo, E., Carrillo Beltrán, R., Perea Toledo, G. E., Corpas Iglesias, F. A., Bogataj, V. Ž., Kotnik, S., & Iglesias Godino, F. J. (2026). Industrial-Scale Injection Moulding Validation of Recycled Fiber-Reinforced Polypropylene: Processability and Manufacturing Feasibility. Materials, 19(11), 2314. https://doi.org/10.3390/ma19112314
Vancouver
Picazo Camilo E, Carrillo Beltrán R, Perea Toledo GE, Corpas Iglesias FA, Bogataj VŽ, Kotnik S, et al. Industrial-Scale Injection Moulding Validation of Recycled Fiber-Reinforced Polypropylene: Processability and Manufacturing Feasibility. Materials. 2026;19(11):2314. doi:10.3390/ma19112314
BibTeX
@article{PicazoCamilo2026,
author = {Picazo Camilo, Elena and Carrillo Beltrán, Raúl and Perea Toledo, Griselda Elisabeth and Corpas Iglesias, Francisco Antonio and Bogataj, Vesna Žepič and Kotnik, Simon and Iglesias Godino, Francisco Javier},
title = {Industrial-Scale Injection Moulding Validation of Recycled Fiber-Reinforced Polypropylene: Processability and Manufacturing Feasibility},
journal = {Materials},
year = {2026},
volume = {19},
number = {11},
pages = {2314},
doi = {10.3390/ma19112314}
}
EUVIMED