EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development of 3D-Printed Cementitious Layered Model Rocks with Recycled Waste: A Study on Anisotropy

Yongbo Hu, Yugao Wang, Zhenxing Wang, Shuying Wang, Jinsong Hu, Lehua Wang, Xiaoliang Xu

Materials · 15.05.2026 · 19 (10) · 2067

DOI: 10.3390/ma19102067 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 15.05.2026. Verfasst von Yongbo Hu und 6 weiteren Autor:innen. Beteiligte Einrichtung: Key Laboratory of Geological Hazards on Three Gorges Reservoir Area of Ministry of Education, China Three Gorges University, 8 Daxue Road, Yichang 44…. Die Arbeit nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Innovation Group Project of Hubei Natural Science Foundation, Research and Innovation Fund of the College of Civil Engineering & Architecture, Three Gorges University, China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Understanding the anisotropy in the physical and mechanical properties of layered rocks is essential for predicting and preventing instability in layered rock masses. However, in-situ sampling is often hindered by the difficulty of obtaining specimens with controlled bedding orientations. Cement-based 3D printing (3DP) offers an efficient approach for fabricating rock analogues, yet the inherent anisotropy induced by the layer-by-layer deposition process has not been well characterized, hindering its broader application. The objectives of this study are (i) to systematically evaluate the intrinsic anisotropy of cement-based 3DP rocks and (ii) to compare the mechanical anisotropy and failure modes of 3DP layered rocks with those of natural layered sandstone. The key findings are as follows: (1) The uniaxial compressive strength (UCS), P-wave velocity, and computed tomography (CT) number of the 3DP rock vary by less than 6% among the X-, Y-, and Z-directions, indicating lower intrinsic anisotropy compared to typical sandstones and several other natural rocks. (2) The UCS, elastic modulus, and secant modulus of the 3DP layered rocks all decrease initially and then increase with bedding dip angle, reaching a minimum at 60°. (3) The main fracture characteristics of the 3DP layered rocks are similar to those of layered sandstone; notably, the 3DP layered soft rock exhibits the most pronounced shear failure features. This study quantifies the low intrinsic anisotropy of cement-based 3DP rocks and validates their similarity to natural layered sandstone in both mechanical anisotropy and failure modes. It thereby provides a reliable, reproducible basis for physical modeling of layered rock masses using 3DP, offering a new approach for laboratory-scale investigations of layered rocks.

Schlagwörter

Stichwörter der Autor:innen

3D printingCT scananisotropyfailure modelayered rockssolid waste

Autor:innen und Institutionen

  • Key Laboratory of Geological Hazards on Three Gorges Reservoir Area of Ministry of Education, China Three Gorges University, 8 Daxue Road, Yichang 443002, China.
  • Jilin Polytechnic of Water Resources and Electric Engineering, 6566 Juye Street, Changchun 130117, China.
  • China Three Gorges Corporation, 1 Liuhe Road, Wuhan 430010, China.
  • Xiantao Anjie Highway Maintenance Co., Ltd., 3 Hanjiang Road, Xiantao 433000, China.

Förderung

  • National Natural Science Foundation of China
  • Innovation Group Project of Hubei Natural Science Foundation
  • Research and Innovation Fund of the College of Civil Engineering & Architecture, Three Gorges University, China

Zitieren

APA

Hu, Y., Wang, Y., Wang, Z., Wang, S., Hu, J., Wang, L., & Xu, X. (2026). Development of 3D-Printed Cementitious Layered Model Rocks with Recycled Waste: A Study on Anisotropy. Materials, 19(10), 2067. https://doi.org/10.3390/ma19102067

Vancouver

Hu Y, Wang Y, Wang Z, Wang S, Hu J, Wang L, et al. Development of 3D-Printed Cementitious Layered Model Rocks with Recycled Waste: A Study on Anisotropy. Materials. 2026;19(10):2067. doi:10.3390/ma19102067

BibTeX
@article{Hu2026,
  author = {Hu, Yongbo and Wang, Yugao and Wang, Zhenxing and Wang, Shuying and Hu, Jinsong and Wang, Lehua and Xu, Xiaoliang},
  title = {Development of 3D-Printed Cementitious Layered Model Rocks with Recycled Waste: A Study on Anisotropy},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {10},
  pages = {2067},
  doi = {10.3390/ma19102067}
}
Kostenlos starten →