EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Process Parameters Optimization of Rotary Friction Welding of Silicon Bronze CuSi3Fe2Zn3 Alloy Using Response Surface Methodology

Henrique Pereira Machado iD, Francisco Yastami Nakamoto iD, Givanildo Alves Dos Santos iD, Gilmar Ferreira Batalha iD, Vinicius Torres do Santos iD, Marcio Rodrigues da Silva iD, Flávia Gonçalves Lobo

Materials · 02.05.2026 · 19 (9) · 1877

DOI: 10.3390/ma19091877 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 02.05.2026. Verfasst von Henrique Pereira Machado und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Engineering, Federal Institute of Education, Science and Technology of São Paulo, São Paulo 01109-010, Brazil. Die Arbeit nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: CAPES—Coordenação de Aperfeiçoamento de Pessoal de Nível Superior.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigates the optimization of selected process parameters in the rotary friction welding (RFW) process of CuSi3Fe2Zn3 silicon bronze alloys using Response Surface Methodology (RSM) with tensile strength as the primary response. The effects of rotation speed, friction time and friction pressure were evaluated, and the steepest ascent method was applied to determine the best parameters. The results indicated that rotation speed and friction time were the most influential parameters for enhancing tensile strength. A maximum tensile of 424 MPa was achieved under conditions of 3300 rpm, friction time of 25 s, friction pressure of 0.5 MPa, forging time of 16 s, and forging pressure of 8 MPa. However, confirmation experiments exhibited noticeable variability, indicating limitations in process repeatability. Tensile properties, hardness evaluation, microstructural characterization, and thermographic analysis were conducted to assess the quality of the welded joints. Microstructural analysis revealed recrystallized equiaxed grains in the welding center zone, consistent with severe plastic deformation, while microcracks and microvoids were observed and likely contributed for failure during tensile testing. Despite grain refinement, a reduction in microhardness was detected, suggesting the influence of thermal softening mechanisms. Thermographic analysis indicated that the average temperature at the welding center zone reached 564 °C. In conclusion, RSM proved to be a useful tool for identifying trends and guiding process optimization. The results highlight the importance of process stability and control in achieving consistent performance in RFW of copper-based alloys.

Schlagwörter

Stichwörter der Autor:innen

microstructureresponse surface methodologyrotary friction weldingsilicon bronzetensile strength

Autor:innen und Institutionen

  • Department of Engineering, Federal Institute of Education, Science and Technology of São Paulo, São Paulo 01109-010, Brazil.
  • Polytechnic School, University of São Paulo, São Paulo 05508-010, Brazil.
  • Research and Development of Termomecanica São Paulo S.A., São Bernardo do Campo 09612-000, Brazil.

ORCID-Profile: Henrique Pereira Machado, Francisco Yastami Nakamoto, Givanildo Alves Dos Santos, Gilmar Ferreira Batalha, Vinicius Torres do Santos, Marcio Rodrigues da Silva

Förderung

  • CAPES—Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Zitieren

APA

Machado, H. P., Nakamoto, F. Y., Santos, G. A. D., Batalha, G. F., Santos, V. T. D., Silva, M. R. D., & Lobo, F. G. (2026). Process Parameters Optimization of Rotary Friction Welding of Silicon Bronze CuSi3Fe2Zn3 Alloy Using Response Surface Methodology. Materials, 19(9), 1877. https://doi.org/10.3390/ma19091877

Vancouver

Machado HP, Nakamoto FY, Santos GAD, Batalha GF, Santos VTD, Silva MRD, et al. Process Parameters Optimization of Rotary Friction Welding of Silicon Bronze CuSi3Fe2Zn3 Alloy Using Response Surface Methodology. Materials. 2026;19(9):1877. doi:10.3390/ma19091877

BibTeX
@article{Machado2026,
  author = {Machado, Henrique Pereira and Nakamoto, Francisco Yastami and Santos, Givanildo Alves Dos and Batalha, Gilmar Ferreira and Santos, Vinicius Torres do and Silva, Marcio Rodrigues da and Lobo, Flávia Gonçalves},
  title = {Process Parameters Optimization of Rotary Friction Welding of Silicon Bronze CuSi3Fe2Zn3 Alloy Using Response Surface Methodology},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {9},
  pages = {1877},
  doi = {10.3390/ma19091877}
}
Kostenlos starten →