EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Study on D6AC Steel PCBN Hard Turning and Optimization

Yihan Liu, Shutao Huang, Ruyu Li, Zhonghan Cui iD, Yupu Zhang, Chengwei Liu

Materials · 30.04.2026 · 19 (9) · 1850

DOI: 10.3390/ma19091850 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 30.04.2026. Verfasst von Yihan Liu und 5 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory Management Center, Shenyang Ligong University, Shenyang 110159, China. Die Arbeit nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This investigation uses polycrystalline cubic boron nitride (PCBN) tools for precision turning of D6AC (45CrNiMoVA) hardened steel, thereby enabling the manufacturing of components that meet the requirements of intelligent manufacturing lines. A Taguchi’s L16 (43) orthogonal design was employed to systematically investigate the effects of cutting speed, depth of cut, and feed rate on cutting force, cutting temperature, surface roughness, and tool wear. Analysis of variance (ANOVA) was then conducted to quantify the contribution of each cutting parameter, and high-accuracy predictive models (R2 > 0.86) were established for the key response variables, namely cutting force components (Fx, Fy, Fz), cutting temperature (T), and flank wear width (VBmax). The results show that excellent surface quality can be achieved within the investigated range, namely at cutting speeds of 100–250 m·min−1, depths of cut of 0.05–0.2 mm, and feed rates of 0.05–0.125 mm·rev−1, with surface roughness (Ra) below 0.8 μm and mostly around 0.4 µm. At a feed rate of 0.05 mm·rev−1, the measured Ra was greater than the theoretical value (Ra*), whereas at a feed rate of 0.075 mm·rev−1, Ra was lower than Ra*, with the difference increasing as feed rate increased. The ANOVA results showed that cutting forces were dominated by depth of cut, cutting temperatures by feed rate, and tool wear by depth of cut. The optimal process strategy was derived as follows: first, prioritize a lower feed rate; second, select an appropriate depth of cut based on tool failure or deformation control objectives; and third, choose a suitable cutting speed according to tool-life requirements or machining efficiency. This study provides process guidance and predictive tools for PCBN finishing of D6AC steel, thus promoting green, precise, and efficient machining of high-strength, high-hardness, and low-thermal-conductivity materials.

Schlagwörter

Stichwörter der Autor:innen

ANOVAD6ACGRAPCBNhard turningprocesses

Autor:innen und Institutionen

  • Laboratory Management Center, Shenyang Ligong University, Shenyang 110159, China.
  • School of Mechanical Engineering, Shenyang Ligong University, Shenyang 110159, China.
  • Innovation and Entrepreneurship College, Shenyang Ligong University, Shenyang 110159, China.

ORCID-Profile: Zhonghan Cui

Zitieren

APA

Liu, Y., Huang, S., Li, R., Cui, Z., Zhang, Y., & Liu, C. (2026). Study on D6AC Steel PCBN Hard Turning and Optimization. Materials, 19(9), 1850. https://doi.org/10.3390/ma19091850

Vancouver

Liu Y, Huang S, Li R, Cui Z, Zhang Y, Liu C. Study on D6AC Steel PCBN Hard Turning and Optimization. Materials. 2026;19(9):1850. doi:10.3390/ma19091850

BibTeX
@article{Liu2026,
  author = {Liu, Yihan and Huang, Shutao and Li, Ruyu and Cui, Zhonghan and Zhang, Yupu and Liu, Chengwei},
  title = {Study on D6AC Steel PCBN Hard Turning and Optimization},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {9},
  pages = {1850},
  doi = {10.3390/ma19091850}
}
Kostenlos starten →