EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Evolution of the Young’s Modulus of Al-7Si-4Cu Alloy with Increasing Temperature by Various Strengthening Approaches

Hongyu Wang, Jingyi Hu, Tong Gao iD, Hongfu Su, Shushuai Liu iD, Xiangfa Liu

Materials · 29.04.2026 · 19 (9) · 1831

DOI: 10.3390/ma19091831 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 29.04.2026. Verfasst von Hongyu Wang und 5 weiteren Autor:innen. Beteiligte Einrichtung: Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Shandong University, 17923 Jingshi Road, Jin…. Die Arbeit nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Despite the crucial role of Young’s modulus in the structural performance of Al alloys, the effects of common strengthening approaches on its evolution, particularly at elevated temperatures, remain largely unexplored. In this study, an Al-7Si-4Cu alloy was modified by hot deformation, micro-alloying with 0.3 wt.% Sc, alloying with 4 wt.% Ni, and reinforcement with 0.8 vol.% Al2O3 nanoparticles. The effects of these strengthening approaches on the microstructure and the evolution of Young’s modulus from room temperature to 350 °C were examined. It was found that the Young’s modulus of the alloys decreased with the increase in temperature, while this tendency is much more obvious when the temperature exceeds 250 °C. The results showed that hot deformation markedly refines the α-Al grains while the Young’s modulus stays largely unchanged. The Sc addition leads to the formation of the W phase but has no significant effect on the Young’s modulus. In contrast, the addition of Ni substantially increases the Young’s modulus through the formation of Al3CuNi intermetallic particles, with the Young’s modulus increasing from 72.15 to 76.47 GPa. With the addition of Al2O3 particles, the decreasing magnitude of Young’s modulus is optimized when the temperature is higher than 250 °C. This work may be referred to when designing high-modulus Al alloys by considering the utilization of various strengthening concepts.

Schlagwörter

Stichwörter der Autor:innen

Al-Si-Cu alloyYoung’s modulushigh temperaturestrengthening

Autor:innen und Institutionen

  • Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials, Ministry of Education, Shandong University, 17923 Jingshi Road, Jinan 250061, China.
  • State Key Laboratory of Coatings for Advanced Equipment, Shandong University, 17923 Jingshi Road, Jinan 250061, China.

ORCID-Profile: Tong Gao, Shushuai Liu

Förderung

  • National Natural Science Foundation of China

Zitieren

APA

Wang, H., Hu, J., Gao, T., Su, H., Liu, S., & Liu, X. (2026). Evolution of the Young’s Modulus of Al-7Si-4Cu Alloy with Increasing Temperature by Various Strengthening Approaches. Materials, 19(9), 1831. https://doi.org/10.3390/ma19091831

Vancouver

Wang H, Hu J, Gao T, Su H, Liu S, Liu X. Evolution of the Young’s Modulus of Al-7Si-4Cu Alloy with Increasing Temperature by Various Strengthening Approaches. Materials. 2026;19(9):1831. doi:10.3390/ma19091831

BibTeX
@article{Wang2026,
  author = {Wang, Hongyu and Hu, Jingyi and Gao, Tong and Su, Hongfu and Liu, Shushuai and Liu, Xiangfa},
  title = {Evolution of the Young’s Modulus of Al-7Si-4Cu Alloy with Increasing Temperature by Various Strengthening Approaches},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {9},
  pages = {1831},
  doi = {10.3390/ma19091831}
}
Kostenlos starten →