EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Minimum and Maximum Void Ratios of Sand–Rubber and Crushed Concrete–Rubber Mixtures

Magdalena Kowalska iD, Bartosz Bdzionek, Katarzyna Gabryś iD, Iwo Zatorski, Cristiana Ferreira iD

Materials · 23.04.2026 · 19 (9) · 1721

DOI: 10.3390/ma19091721 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 23.04.2026. Verfasst von Magdalena Kowalska und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Geotechnics and Roads, Faculty of Civil Engineering, Silesian University of Technology, Akademicka 5, 44-100 Gliwice, Poland. Die Arbeit nennt 73 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science Centre, Silesian University of Technology, National Science Centre, Poland.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

There are no unique and universally accepted procedures for the determination of the maximum and minimum void ratios, emax and emin. This issue is particularly pertinent in the characterisation of the alternative sustainable materials examined in this study: well-graded tyre-derived aggregate (TDA), recycled concrete aggregate (RCA) and their mixtures (RCA-TDA), with a rubber content by weight of ΧM = 11, 23 and 55%. Uniformly graded TDA–sand mixtures with ΧM = 0, 15, 27, 42, and 100% were also considered. The results from dry and moist samples were compared with void ratios obtained after Proctor compaction and static loading. It was found that, in contrast to vibration for sand and sand–TDA mixtures, the most efficient densification techniques involve impact compaction at the optimum water content for RCA and RCA-TDA and static loading for TDA. Inversion of dry RCA, TDA and RCA-TDA samples in a graduated cylinder was the most effective to consistently achieve emax but induced visible segregation. Unlike sand–rubber mixtures, well-graded RCA-TDA did not exhibit a threshold rubber content at which emax and emin fell below those of RCA and TDA alone, suggesting reduced segregation. The findings offer practical guidance for improving specimen preparation reproducibility in the laboratory.

Schlagwörter

Stichwörter der Autor:innen

Proctor testmaximum and minimum void ratiosrecycled concrete aggregatescrap tyre rubbervibration

Autor:innen und Institutionen

  • Department of Geotechnics and Roads, Faculty of Civil Engineering, Silesian University of Technology, Akademicka 5, 44-100 Gliwice, Poland.
  • Faculty of Civil Engineering, Silesian University of Technology, Akademicka 5, 44-100 Gliwice, Poland.
  • Department of Geotechnics, Institute of Civil Engineering, Warsaw University of Life Sciences, Nowoursynowska 159, 02-776 Warsaw, Poland.
  • Institute of Civil Engineering, Warsaw University of Life Sciences, Nowoursynowska 159, 02-776 Warsaw, Poland.
  • CONSTRUCT-GEO, Faculty of Engineering, University of Porto (FEUP), Rua Roberto Frias, s/n, 4200-465 Porto, Portugal.

ORCID-Profile: Magdalena Kowalska, Katarzyna Gabryś, Cristiana Ferreira

Förderung

  • National Science Centre
  • Silesian University of Technology
  • National Science Centre, Poland

Zitieren

APA

Kowalska, M., Bdzionek, B., Gabryś, K., Zatorski, I., & Ferreira, C. (2026). Minimum and Maximum Void Ratios of Sand–Rubber and Crushed Concrete–Rubber Mixtures. Materials, 19(9), 1721. https://doi.org/10.3390/ma19091721

Vancouver

Kowalska M, Bdzionek B, Gabryś K, Zatorski I, Ferreira C. Minimum and Maximum Void Ratios of Sand–Rubber and Crushed Concrete–Rubber Mixtures. Materials. 2026;19(9):1721. doi:10.3390/ma19091721

BibTeX
@article{Kowalska2026,
  author = {Kowalska, Magdalena and Bdzionek, Bartosz and Gabryś, Katarzyna and Zatorski, Iwo and Ferreira, Cristiana},
  title = {Minimum and Maximum Void Ratios of Sand–Rubber and Crushed Concrete–Rubber Mixtures},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {9},
  pages = {1721},
  doi = {10.3390/ma19091721}
}
Kostenlos starten →