EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Analysis of Strength and Homogeneity of Different Concrete Specimens Prepared Under a High-Frequency and Low-Power Piezoelectric Excitation System

Nabi İbadov iD, Gürcan Çetin iD, Ercüment Güvenç iD, Murat Çevikbaş iD, İsmail Serkan Üncü iD, Kamil Furkan İlhan

Materials · 16.04.2026 · 19 (8) · 1600

DOI: 10.3390/ma19081600 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 16.04.2026. Verfasst von Nabi İbadov und 5 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Civil Engineering, Department of Production Engineering and Management in Construction, Warsaw University of Technology, Al. Armii Ludowej…. Die Arbeit nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Muğla Sıtkı Koçman University Scientific Research Projects (BAP) Coordination Unit.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ensuring the durability and safety of modern infrastructure critically depends on the quality and strength of concrete. The Ultrasonic Pulse Velocity (UPV) method is a widely used non-destructive testing technique for evaluating concrete properties; however, factors such as aggregate size distribution, compaction methods, and surface quality can significantly influence UPV results and their correlation with compressive strength. This study investigates the effects of different aggregate sizes and an innovative vibration-assisted compaction method—developed using piezoelectric (PZT) transducers—on the mechanical, ultrasonic, and surface properties of concrete. Four distinct aggregate size distributions were employed to produce sixteen concrete specimens with constant mix proportions. Unlike conventional low-frequency, high-power vibration practices, a high-frequency (40 kHz), low-power (120 W) vibration protocol was applied through PZT elements placed within the molds to enhance compaction and reduce entrapped air. Experimental results indicated that the heaviest specimen (7.13 kg) was the medium-aggregate sample compacted using tamping and rodding methods. The highest UPV value (4143 m/s) was obtained from the coarse-aggregate specimen subjected to three minutes of vibration. In contrast, the best compressive strength performance (22.73 MPa) was observed in the medium-aggregate specimen without any vibration treatment. The findings revealed that both aggregate size and advanced vibration techniques have significant effects on the mechanical properties, ultrasonic response, and surface quality of concrete. In addition, a proof-of-concept portable surface-finishing prototype consisting of a steel plate instrumented with multiple PZT transducers was developed, and preliminary trials qualitatively suggested improved surface leveling when applied in contact with the concrete surface. Surface roughness was quantified via image processing (Light Map 150 and Specular Map 150). The rough-area fraction decreased from ~29.8% in the untreated specimen to ~4.3% after ultrasonic application, indicating a marked improvement in surface leveling and overall surface quality. The results indicate that the applied PZT vibration protocol did not improve compressive strength; in several cases, particularly under prolonged excitation, a reduction in strength was observed. In contrast, a significant improvement in surface quality was achieved, with the rough-area fraction decreasing from approximately 29.8% to 4.3%. However, due to the limited number of specimens, the findings should be interpreted as preliminary. Overall, the method appears more promising as a surface enhancement technique rather than a direct alternative to conventional compaction methods.

Schlagwörter

Stichwörter der Autor:innen

compressive strengthconcreteimage processingpiezoelectric vibrationsurface roughnessultrasonic pulse velocity

Autor:innen und Institutionen

  • Faculty of Civil Engineering, Department of Production Engineering and Management in Construction, Warsaw University of Technology, Al. Armii Ludowej 16, 00-637 Warszawa, Poland.
  • Information Systems Engineering, Faculty of Technology, Muğla Sıtkı Koçman University, 48000 Muğla, Türkiye.
  • Rectorate Units, Department of Informatics, Muğla Sıtkı Koçman University, 48000 Muğla, Türkiye.
  • Department of Civil Engineering, Faculty of Technology, Isparta University of Applied Sciences, 32040 Isparta, Türkiye.
  • Department of Electrical and Electronics Engineering, Faculty of Technology, Isparta University of Applied Sciences, 32040 Isparta, Türkiye.

ORCID-Profile: Nabi İbadov, Gürcan Çetin, Ercüment Güvenç, Murat Çevikbaş, İsmail Serkan Üncü

Förderung

  • Muğla Sıtkı Koçman University Scientific Research Projects (BAP) Coordination Unit

Zitieren

APA

İbadov, N., Çetin, G., Güvenç, E., Çevikbaş, M., Üncü, İ. S., & İlhan, K. F. (2026). Analysis of Strength and Homogeneity of Different Concrete Specimens Prepared Under a High-Frequency and Low-Power Piezoelectric Excitation System. Materials, 19(8), 1600. https://doi.org/10.3390/ma19081600

Vancouver

İbadov N, Çetin G, Güvenç E, Çevikbaş M, Üncü İS, İlhan KF. Analysis of Strength and Homogeneity of Different Concrete Specimens Prepared Under a High-Frequency and Low-Power Piezoelectric Excitation System. Materials. 2026;19(8):1600. doi:10.3390/ma19081600

BibTeX
@article{badov2026,
  author = {İbadov, Nabi and Çetin, Gürcan and Güvenç, Ercüment and Çevikbaş, Murat and Üncü, İsmail Serkan and İlhan, Kamil Furkan},
  title = {Analysis of Strength and Homogeneity of Different Concrete Specimens Prepared Under a High-Frequency and Low-Power Piezoelectric Excitation System},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {8},
  pages = {1600},
  doi = {10.3390/ma19081600}
}
Kostenlos starten →