EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Correlation Between Manufacturing Conditions, Microstructure, and Electrical–Mechanical Properties of Cu Matrix Composites

Marko Simić, Emilija Nidžović, Svetlana Butulija iD, Željko Radovanović iD, Marija M Vuksanović iD, Jovana Ružić iD

Materials · 28.03.2026 · 19 (7) · 1347

DOI: 10.3390/ma19071347 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 28.03.2026. Verfasst von Marko Simić und 5 weiteren Autor:innen. Beteiligte Einrichtung: "Vinča" Institute of Nuclear Sciences-National Institute of the Republic of Serbia, University of Belgrade, 11001 Belgrade, Serbia. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science Fund of the Republic of Serbia, Serbian Ministry of Education, Science, and Technological Development.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The continuous demand for advanced composite materials with superior mechanical and electrical properties has driven the exploration of copper matrix composites for high-performance applications. The Cu–2Zr–0.6B (wt.%) powder mixtures were mechanically alloyed (MA) using two different ball-to-powder weight ratios (BPR: 10:1 and 15:1) to investigate the influence of milling conditions on the final composite material’s properties. MA powders milled with BPR 15:1 exhibited the highest values of dislocation densities, which induce higher hardness of Cu–ZrB2 bulk materials. The MA powders were consolidated using three different methods: conventional cold pressing followed by sintering (CPS), hot pressing (HP), and spark plasma sintering (SPS). The in situ forming of ZrB2 (3.5 vol.%) reinforcements during consolidation processes in Cu matrix proved to have a major impact on enhancing the hardness and structural stability, while the use of SPS and HP offered superior control over grain growth and porosity reduction compared to CPS. Main findings related to electrical and mechanical properties showed similar values for SPS (~38% IACS, ~173 HV1) and HP compacts (~39% IACS, ~155 HV1) but proved to be much higher compared to values of CPS compacts (~21% IACS, ~80 HV1).

Schlagwörter

Stichwörter der Autor:innen

Cu–matrix compositesconductivitymechanical alloyingmechanical propertiespowder metallurgy

Autor:innen und Institutionen

  • "Vinča" Institute of Nuclear Sciences-National Institute of the Republic of Serbia, University of Belgrade, 11001 Belgrade, Serbia.
  • Innovation Center of the Faculty of Technology and Metallurgy, Ltd., Karnegijeva 4, 11120 Belgrade, Serbia.

ORCID-Profile: Svetlana Butulija, Željko Radovanović, Marija M Vuksanović, Jovana Ružić

Förderung

  • Science Fund of the Republic of Serbia
  • Serbian Ministry of Education, Science, and Technological Development

Zitieren

APA

Simić, M., Nidžović, E., Butulija, S., Radovanović, Ž., Vuksanović, M. M., & Ružić, J. (2026). Correlation Between Manufacturing Conditions, Microstructure, and Electrical–Mechanical Properties of Cu Matrix Composites. Materials, 19(7), 1347. https://doi.org/10.3390/ma19071347

Vancouver

Simić M, Nidžović E, Butulija S, Radovanović Ž, Vuksanović MM, Ružić J. Correlation Between Manufacturing Conditions, Microstructure, and Electrical–Mechanical Properties of Cu Matrix Composites. Materials. 2026;19(7):1347. doi:10.3390/ma19071347

BibTeX
@article{Simi2026,
  author = {Simić, Marko and Nidžović, Emilija and Butulija, Svetlana and Radovanović, Željko and Vuksanović, Marija M and Ružić, Jovana},
  title = {Correlation Between Manufacturing Conditions, Microstructure, and Electrical–Mechanical Properties of Cu Matrix Composites},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {7},
  pages = {1347},
  doi = {10.3390/ma19071347}
}
Kostenlos starten →