EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Properties of Laser-Welded Zr-Al-Co-Nb Bulk Metallic Glass

Huei-Sen Wang, Chih-Chun Hsieh iD, Hou-Guang Chen iD, Shao-Chi Wu, Jason Shian-Ching Jang iD, Kuo-Jung Lee

Materials · 11.03.2026 · 19 (6) · 1078

DOI: 10.3390/ma19061078 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 11.03.2026. Verfasst von Huei-Sen Wang und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Engineering, I-Shou University, Kaohsiung City 84001, Taiwan. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science and Technology Council of Taiwan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, the Nd:YAG laser process was employed with preselected welding parameters and varying initial welding temperatures (including room temperature, 10 °C, and 0 °C) for spot welding of (Zr53Al17Co29)Nb1 bulk metallic glass. Following welding, the microstructure—including the parent material, heat-affected zone (HAZ), and weld fusion zone (WFZ)—as well as the microhardness, thermal properties, and corrosion resistance of the welds, were systematically investigated. Owing to the low glass-forming ability of the alloy, a small amount of Zr6CoAl2 phase was observed within the amorphous matrix at the center of the bulk metallic glass cast plate. After the laser welding, sub-micron or nanoscale Zr(AlxCo1−x)2 phases have formed in the HAZ of all welded samples, which significantly influenced the microhardness, thermal properties, and corrosion resistance in this region. As the initial welding temperature decreased, both the volume fraction and the density of the Zr(AlxCo1−x)2 phase were reduced. Notably, for the weld performed at the lowest initial temperature of 0 °C, small crystalline phases were detected only at approximately 70 μm below the surface of the HAZ. To clarify the effect of IWTs on corrosion resistance, welded samples were immersed in 6 M HCl at 35 °C for 72–120 h. Surface morphologies after corrosion were examined by SEM in the PM, HAZ, and WFZ. No evident pitting was detected after 72 h of immersion. After 120 h, pitting corrosion was observed on the HAZ surfaces of welds subjected to RT and 10 °C IWTs, whereas no obvious pitting was found at an IWT of 0 °C. The pit size and density in the HAZ increased with increasing IWT. In contrast, no pitting was observed in the WFZ under any IWT condition.

Schlagwörter

Stichwörter der Autor:innen

bulk metallic glasscorrosion resistancemicrohardnessmicrostructurethermal propertieswelding

Autor:innen und Institutionen

  • Department of Materials Science and Engineering, I-Shou University, Kaohsiung City 84001, Taiwan.
  • Institute of Material Science and Engineering, National Central University, Taoyuan 32001, Taiwan.

ORCID-Profile: Chih-Chun Hsieh, Hou-Guang Chen, Jason Shian-Ching Jang

Förderung

  • National Science and Technology Council of Taiwan

Zitieren

APA

Wang, H. S., Hsieh, C. C., Chen, H. G., Wu, S. C., Jang, J. S., & Lee, K. J. (2026). Properties of Laser-Welded Zr-Al-Co-Nb Bulk Metallic Glass. Materials, 19(6), 1078. https://doi.org/10.3390/ma19061078

Vancouver

Wang HS, Hsieh CC, Chen HG, Wu SC, Jang JS, Lee KJ. Properties of Laser-Welded Zr-Al-Co-Nb Bulk Metallic Glass. Materials. 2026;19(6):1078. doi:10.3390/ma19061078

BibTeX
@article{Wang2026,
  author = {Wang, Huei-Sen and Hsieh, Chih-Chun and Chen, Hou-Guang and Wu, Shao-Chi and Jang, Jason Shian-Ching and Lee, Kuo-Jung},
  title = {Properties of Laser-Welded Zr-Al-Co-Nb Bulk Metallic Glass},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {6},
  pages = {1078},
  doi = {10.3390/ma19061078}
}
Kostenlos starten →