The Effect of Initial Microstructure and Hardenability on Diode Laser Surface Hardening of Medium-Carbon Steels
Materials · 03.03.2026 · 19 (5) · 981
DOI: 10.3390/ma19050981 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 03.03.2026. Verfasst von Lyubomir Lazov und 10 weiteren Autor:innen. Beteiligte Einrichtung: Rezekne Academy of Riga Technical University, Atbrivosanas Aleja 115, LV-4601 Rezekne, Latvia. Die Arbeit nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: RTU Project: 5.2.1.1.i.0/2/24/I/CFLA/003 (Implementation of consolidation and management changes at RTU, LiepU, Rēzekne Academy of Technology and Latvian Marit….
Abstract (Originalsprache)
This study systematically investigates the laser surface hardening (LSH) behavior of two medium carbon steels—the low alloy 42CrMo4 and the plain carbon C45—using a 4 kW high power diode laser (HPDL). The influence of laser parameters (power: 3.0–3.8 kW; scanning speed: 10–16 mm/s), post-laser quenching medium (oil vs. air), and, critically, the initial material condition (normalized “raw” vs. quenched and tempered “Q&T”) on the case hardening depth (CHD) was evaluated. Hardness profiles defined the CHD at a threshold of 392 HV1, and microstructural analysis was conducted via optical microscopy. The results demonstrate that prior conventional Q&T heat treatment of 42CrMo4 enhances the subsequent laser-hardened depth by approximately 27% compared to laser treatment of the normalized material under identical parameters, providing a quantitative basis for process optimization. For Q&T 42CrMo4, the quenching medium had an insignificant effect on CHD, with air cooling proving equally effective as oil across the tested parameter range, offering an empirically validated route for sustainable processing. In contrast, C45 exhibited a substantially lower and less parameter-sensitive CHD, constrained by its inherent low hardenability. This comparative analysis underscores that hardening depth in 42CrMo4 is linearly controllable via energy input, whereas for C45 it is hardenability-limited. This work establishes that an integrated approach combining conventional bulk heat treatment with diode laser hardening using air cooling offers a highly effective, controllable, and sustainable surface engineering route for high-performance alloy steels.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Rezekne Academy of Riga Technical University, Atbrivosanas Aleja 115, LV-4601 Rezekne, Latvia.
- BMF Institute of Mechanical and Biomedical Engineering, Riga Technical University, 6A Kipsalas Street, LV-1048 Riga, Latvia.
- Faculty of Nuclear Sciences and Physical Engineering, Czech Technical University in Prague, Trojanova 13, 120 00 Prague, Czech Republic.
- Center of Competence "Smart Mechatronic, Eco- and Energy-Saving Systems and Technologies", Technical University of Gabrovo, ul. "Hadji Dimitar" 4, 5300 Gabrovo, Bulgaria.
- Department of Machine Elements and Chemistry, Todor Kableshkov University of Transport, ul. Geo Milev 158, 1574 Sofia, Bulgaria.
ORCID-Profile: Lyubomir Lazov, Gatis Muiznieks, Armands Leitans, Jiří Čapek, Karel Trojan, Prodan Prodanov, Emil Yankov, Ritvars Rēvalds
Förderung
- RTU Project: 5.2.1.1.i.0/2/24/I/CFLA/003 (Implementation of consolidation and management changes at RTU, LiepU, Rēzekne Academy of Technology and Latvian Marit…
Zitieren
APA
Lazov, L., Teirumnieks, E., Muiznieks, G., Leitans, A., Čapek, J., Trojan, K., Prodanov, P., Yankov, E., Teirumnieks, N., Rēvalds, R., & Adijāns, I. (2026). The Effect of Initial Microstructure and Hardenability on Diode Laser Surface Hardening of Medium-Carbon Steels. Materials, 19(5), 981. https://doi.org/10.3390/ma19050981
Vancouver
Lazov L, Teirumnieks E, Muiznieks G, Leitans A, Čapek J, Trojan K, et al. The Effect of Initial Microstructure and Hardenability on Diode Laser Surface Hardening of Medium-Carbon Steels. Materials. 2026;19(5):981. doi:10.3390/ma19050981
BibTeX
@article{Lazov2026,
author = {Lazov, Lyubomir and Teirumnieks, Edmunds and Muiznieks, Gatis and Leitans, Armands and Čapek, Jiří and Trojan, Karel and Prodanov, Prodan and Yankov, Emil and Teirumnieks, Normunds and Rēvalds, Ritvars and Adijāns, Imants},
title = {The Effect of Initial Microstructure and Hardenability on Diode Laser Surface Hardening of Medium-Carbon Steels},
journal = {Materials},
year = {2026},
volume = {19},
number = {5},
pages = {981},
doi = {10.3390/ma19050981}
}
EUVIMED