EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative Study on Thermal Behaviour, Tool Wear and Surface Roughness in Milling EN8 Steel for Sustainable Machining

Thenarasu Mohanavelu iD, Narassima Madhavarao Seshadri, Sreeranjani Vijayakumar iD, Sumesh Arangot iD, Jana Petru iD, Saravanamurugan Sundaram iD

Materials · 03.03.2026 · 19 (5) · 975

DOI: 10.3390/ma19050975 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 03.03.2026. Verfasst von Thenarasu Mohanavelu und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore 641112, India. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Dry machining of medium-carbon steels plays an important role in sustainable manufacturing; however, high tool wear and thermal instability pose challenges. The study aims to evaluate the kinematic–tribological performance of EN8 steel during dry milling and compare up-milling and down-milling to trade-off tool life and surface finish. The experiments were conducted using a central composite design (CCD) as part of response surface methodology (RSM), with 36 runs to evaluate interactions among spindle speed, feed rate, and depth of cut. Down-milling outperformed up-milling, achieving 12.4% less tool wear, 45.9% better surface finish, and a 47 °C lower peak temperature from cutting. The above benefits are attributed to the unique kinematics of chip formation during down-milling, which offers lower friction at entry and better heat dissipation, contrasting with the high-friction ploughing phase of up-milling. Grey relational analysis (GRA) found that down-milling with a mid-range cutting speed (22.31 m/min) and a low feed rate (25 mm/min) provided a multi-objective optimum. The findings support the existence of a kinematic–tribological coupling, providing a solid single approach to optimising the dry machining of harder materials.

Schlagwörter

Stichwörter der Autor:innen

grey relational analysis (GRA)response surface methodology (RSM)sustainable machiningthermal imagingtool wear and surface roughness

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore 641112, India.
  • Great Lakes Institute of Management, Chennai 603102, India.
  • Department of Machining, Assembly and Engineering Metrology, Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 70800 Ostrava, Czech Republic.

ORCID-Profile: Thenarasu Mohanavelu, Sreeranjani Vijayakumar, Sumesh Arangot, Jana Petru, Saravanamurugan Sundaram

Zitieren

APA

Mohanavelu, T., Seshadri, N. M., Vijayakumar, S., Arangot, S., Petru, J., & Sundaram, S. (2026). Comparative Study on Thermal Behaviour, Tool Wear and Surface Roughness in Milling EN8 Steel for Sustainable Machining. Materials, 19(5), 975. https://doi.org/10.3390/ma19050975

Vancouver

Mohanavelu T, Seshadri NM, Vijayakumar S, Arangot S, Petru J, Sundaram S. Comparative Study on Thermal Behaviour, Tool Wear and Surface Roughness in Milling EN8 Steel for Sustainable Machining. Materials. 2026;19(5):975. doi:10.3390/ma19050975

BibTeX
@article{Mohanavelu2026,
  author = {Mohanavelu, Thenarasu and Seshadri, Narassima Madhavarao and Vijayakumar, Sreeranjani and Arangot, Sumesh and Petru, Jana and Sundaram, Saravanamurugan},
  title = {Comparative Study on Thermal Behaviour, Tool Wear and Surface Roughness in Milling EN8 Steel for Sustainable Machining},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {5},
  pages = {975},
  doi = {10.3390/ma19050975}
}
Kostenlos starten →