EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Tailoring the Mechanical Properties of Al0.4CrFe2Ni2 Medium-Entropy Alloy via Thermomechanical Processing

Róbert Kočiško iD, Patrik Petroušek iD, Ondrej Milkovič, Pavel Diko, Vladimír Girman, Andrea Sütőová iD, Michal Duchek iD, Michal Zemko iD

Materials · 27.01.2026 · 19 (3) · 502

DOI: 10.3390/ma19030502 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.01.2026. Verfasst von Róbert Kočiško und 7 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Materials, Metallurgy and Recycling, Technical University of Košice, Letná 9, 042 00 Kosice, Slovakia. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: NextGenerationEU through the Recovery and Resilience Plan for Slovakia, NextGenerationEU.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The microstructure and properties of a cobalt-free, cost-effective Al0.4CrFe2Ni2 medium-entropy alloy (MEA) after multi-stage thermomechanical processing, including annealing, rolling over a wide temperature range from hot to cryogenic conditions, and subsequent precipitation strengthening, were investigated in the present study. The initially cast microstructure was effectively homogenized through hot rolling with an 80% thickness reduction followed by homogenization annealing, resulting in the formation of a single-phase supersaturated solid solution and enhanced stability of plastic deformation. Strengthening of the MEA was achieved by rolling under both ambient and cryogenic conditions, with the deformation process predominantly governed by shear band formation. However, rolling under cryogenic conditions led to a more pronounced localization of plastic deformation, promoting the formation of deformation nanotwins and resulting in significantly higher strengthening compared to ambient rolling, with the alloy reaching a yield strength of 1040 MPa and an ultimate tensile strength of 1235 MPa. Precipitation hardening was governed by the formation of B2-type (ordered body-centered cubic, BCC) precipitates, which preferentially nucleated along deformation bands, thereby effectively strengthening the alloy to a yield strength of 1420 MPa and an ultimate tensile strength of 1465 MPa. Our results demonstrate that the investigated MEA offers a wide range of tunable mechanical properties, which can be effectively tailored through appropriate combinations of thermomechanical processing routes.

Schlagwörter

Stichwörter der Autor:innen

cryo-rolledmechanical propertiesmedium-entropy alloysmicrostructural evolutionprecipitation strengtheningthermomechanical processing

Autor:innen und Institutionen

  • Faculty of Materials, Metallurgy and Recycling, Technical University of Košice, Letná 9, 042 00 Kosice, Slovakia.
  • Institute of Materials Research, Slovak Academy of Sciences, Watsonova 47, 040 01 Košice, Slovakia.
  • Institute of Experimental Physics, Slovak Academy of Sciences, Watsonova 47, 040 01 Košice, Slovakia.
  • Institute of Physics, Faculty of Science, P. J. Šafárik University in Košice, Park Angelinum 9, 041 54 Košice, Slovakia.
  • Department of Quality Management, VSB-Technical University of Ostrava, 17. Listopadu, 708 00 Ostrava, Czech Republic.
  • COMTES FHT a.s., Průmyslová 995, 334 41 Dobřany, Czech Republic.

ORCID-Profile: Róbert Kočiško, Patrik Petroušek, Andrea Sütőová, Michal Duchek, Michal Zemko

Förderung

  • NextGenerationEU through the Recovery and Resilience Plan for Slovakia
  • NextGenerationEU

Zitieren

APA

Kočiško, R., Petroušek, P., Milkovič, O., Diko, P., Girman, V., Sütőová, A., Duchek, M., & Zemko, M. (2026). Tailoring the Mechanical Properties of Al0.4CrFe2Ni2 Medium-Entropy Alloy via Thermomechanical Processing. Materials, 19(3), 502. https://doi.org/10.3390/ma19030502

Vancouver

Kočiško R, Petroušek P, Milkovič O, Diko P, Girman V, Sütőová A, et al. Tailoring the Mechanical Properties of Al0.4CrFe2Ni2 Medium-Entropy Alloy via Thermomechanical Processing. Materials. 2026;19(3):502. doi:10.3390/ma19030502

BibTeX
@article{Koiko2026,
  author = {Kočiško, Róbert and Petroušek, Patrik and Milkovič, Ondrej and Diko, Pavel and Girman, Vladimír and Sütőová, Andrea and Duchek, Michal and Zemko, Michal},
  title = {Tailoring the Mechanical Properties of Al0.4CrFe2Ni2 Medium-Entropy Alloy via Thermomechanical Processing},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {3},
  pages = {502},
  doi = {10.3390/ma19030502}
}
Kostenlos starten →