EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Densification Behavior and Microstructure of Nickel Aluminum Bronze Alloy Fabricated by Laser Powder Bed Fusion

Yizhe Huang iD, Guanjun Fu iD, An Wang, Zhongxu Xiao, Jinfeng Sun, Jun Wang iD, Xiaojia Nie iD

Materials · 05.01.2026 · 19 (1) · 208

DOI: 10.3390/ma19010208 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 05.01.2026. Verfasst von Yizhe Huang und 6 weiteren Autor:innen. Beteiligte Einrichtung: Hubei Key Laboratory of Modern Manufacturing Quality Engineering, School of Mechanical Engineering, Hubei University of Technology, Wuhan 430068, Chi…. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Nickel–Aluminum–Bronze (NAB) has gained significant attention in marine applications due to its excellent corrosion resistance and has shown growing potential for laser powder bed fusion (L-PBF) additive manufacturing. However, research on the fabrication of NAB alloys using L-PBF remains relatively limited. In this study, fully dense NAB samples were successfully fabricated through L-PBF process parameter optimization. The microstructural evolution and mechanical properties of both as-built and annealed L-PBF samples were systematically investigated and compared with those of traditionally cast NAB. The results reveal that the as-built L-PBF specimens primarily consist of columnar β′ grains, with the α phase distributed along the grain boundaries and a small amount of κ phase precipitated within the β′ matrix, distinctly different from the cast microstructure characterized by a columnar α-phase matrix with precipitated β′ and κ phases. After annealing at 675 °C for 6 h, the β′ phase in both methods decomposed into α + κ phases, and the original columnar structure in the L-PBF specimens transformed into a dendritic morphology. Compared to the cast samples, the L-PBF-produced NAB alloy exhibited significantly enhanced yield strength, tensile strength, and microhardness, attributable to rapid solidification during the L-PBF process. Following annealing, the yield strength and elongation increased by 12.8% and 184.4%, respectively, compared to the as-built condition, resulting from the decomposition of the martensitic phase into α + κ phases and further grain refinement.

Schlagwörter

Stichwörter der Autor:innen

densification behaviorlaser powder bed fusionmechanical propertymicrostructurenickel–aluminum–bronze alloy

Autor:innen und Institutionen

  • Hubei Key Laboratory of Modern Manufacturing Quality Engineering, School of Mechanical Engineering, Hubei University of Technology, Wuhan 430068, China.
  • Naval University of Engineering, Wuhan 430033, China.

ORCID-Profile: Yizhe Huang, Guanjun Fu, Jun Wang, Xiaojia Nie

Förderung

  • The National Natural Science Foundation of China

Zitieren

APA

Huang, Y., Fu, G., Wang, A., Xiao, Z., Sun, J., Wang, J., & Nie, X. (2026). Densification Behavior and Microstructure of Nickel Aluminum Bronze Alloy Fabricated by Laser Powder Bed Fusion. Materials, 19(1), 208. https://doi.org/10.3390/ma19010208

Vancouver

Huang Y, Fu G, Wang A, Xiao Z, Sun J, Wang J, et al. Densification Behavior and Microstructure of Nickel Aluminum Bronze Alloy Fabricated by Laser Powder Bed Fusion. Materials. 2026;19(1):208. doi:10.3390/ma19010208

BibTeX
@article{Huang2026,
  author = {Huang, Yizhe and Fu, Guanjun and Wang, An and Xiao, Zhongxu and Sun, Jinfeng and Wang, Jun and Nie, Xiaojia},
  title = {Densification Behavior and Microstructure of Nickel Aluminum Bronze Alloy Fabricated by Laser Powder Bed Fusion},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {1},
  pages = {208},
  doi = {10.3390/ma19010208}
}
Kostenlos starten →