EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Titanium Content on the Microstructure and Tensile Behavior of Cold-Spray Additively Manufactured Copper-Titanium Composites

Jia Cheng, Jibo Huang, Haifan Li, Kejie Zhang, Tao Chen, Haiming Lan, Renzhong Huang

Materials · 10.11.2025 · 18 (22) · 5100

DOI: 10.3390/ma18225100 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 10.11.2025. Verfasst von Jia Cheng und 6 weiteren Autor:innen. Beteiligte Einrichtung: China Yangtze Power Co., Ltd., Yichang 443000, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Project of "Feasibility Study of Cold Spray Technology for Repairing Large Hydropower Plant Equipment" from China Yangtze Power Co., Ltd., China Yangtze Power Co., Ltd..

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Cold-spray additive manufacturing (CSAM) is an emerging solid-state deposition technology that effectively mitigates common defects associated with conventional thermal processes, such as oxidation, phase transformation, and residual stresses. In this study, copper–titanium (Cu-Ti) composite coatings were fabricated via high-pressure CSAM using mixed powders with Ti contents of 3, 6, and 10 wt.%. The influence of Ti content and post-heat treatment (350–400 °C) on the tensile properties of the composites was systematically investigated. The results indicate that the ultimate tensile strength (UTS) remained consistently within the range of 265–285 MPa under all conditions, showing only a mild positive correlation with Ti content. In contrast, ductility was significantly influenced by Ti addition, with elongation decreasing markedly as the Ti content increased. Notably, the composite with 3 wt.% Ti heat-treated at 400 °C exhibited a well-balanced combination of tensile strength (270 MPa) and ductility (20% elongation). These findings demonstrate that CSAM-fabricated Cu-Ti composites possess attractive mechanical properties, which can be tailored through Ti content and heat treatment.

Schlagwörter

Stichwörter der Autor:innen

cold-spray additive manufacturingcopper–titanium compositeheat treatmentmicrostructuretensile propertiestitanium content

Autor:innen und Institutionen

  • China Yangtze Power Co., Ltd., Yichang 443000, China.
  • Guangzhou Institute of Hubei Chaozhuo Aviation Technology Co., Ltd., Guangzhou 510530, China.

Förderung

  • Project of "Feasibility Study of Cold Spray Technology for Repairing Large Hydropower Plant Equipment" from China Yangtze Power Co., Ltd.
  • China Yangtze Power Co., Ltd.

Zitieren

APA

Cheng, J., Huang, J., Li, H., Zhang, K., Chen, T., Lan, H., & Huang, R. (2025). Influence of Titanium Content on the Microstructure and Tensile Behavior of Cold-Spray Additively Manufactured Copper-Titanium Composites. Materials, 18(22), 5100. https://doi.org/10.3390/ma18225100

Vancouver

Cheng J, Huang J, Li H, Zhang K, Chen T, Lan H, et al. Influence of Titanium Content on the Microstructure and Tensile Behavior of Cold-Spray Additively Manufactured Copper-Titanium Composites. Materials. 2025;18(22):5100. doi:10.3390/ma18225100

BibTeX
@article{Cheng2025,
  author = {Cheng, Jia and Huang, Jibo and Li, Haifan and Zhang, Kejie and Chen, Tao and Lan, Haiming and Huang, Renzhong},
  title = {Influence of Titanium Content on the Microstructure and Tensile Behavior of Cold-Spray Additively Manufactured Copper-Titanium Composites},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {22},
  pages = {5100},
  doi = {10.3390/ma18225100}
}
Kostenlos starten →