EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

In Vivo Degradation Behaviour and Osteoregenerative Capacity of 3D-Printed Magnesium Phosphate and Calcium Magnesium Phosphate Cement Scaffolds

Sophia Hiepe, Elke Vorndran, Franziska Feichtner, Anja-Christina Waselau, Andrea Meyer-Lindenberg iD

Materials · 07.11.2025 · 18 (22) · 5067

DOI: 10.3390/ma18225067 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 07.11.2025. Verfasst von Sophia Hiepe und 4 weiteren Autor:innen. Beteiligte Einrichtung: Clinic for Small Animal Surgery and Reproduction, Ludwig Maximilians University Munich, 80539 Munich, Germany. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 55 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deutsche Forschungsgemeinschaft, German Research Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Developing bone substitutes that are mechanically strong, highly biocompatible and capable of controlled degradation is crucial for successful bone regeneration. Magnesium phosphate cements (MPCs) and calcium magnesium phosphate cements (CMPCs) offer higher strength and solubility than established calcium phosphate cements (CPCs). This study aimed to evaluate the in vivo degradation, osteoregeneration and biocompatibility of 3D powder-printed Mg3d (Mg3(PO4)2) and Mg275d (Ca0.25Mg2.75(PO4)2) scaffolds with alkaline post-treatment, using structurally identical TCP (Ca3(PO4)2) scaffolds as the control. The scaffolds were implanted into the lateral femoral condyle of adult female Zika rabbits and analysed up to 6, 12 and 24 weeks using radiography, microCT, histology, EDX and SEM. All materials demonstrated good biocompatibility. Mg3d and Mg275d scaffolds degraded significantly faster than the TCP scaffolds, with nearly complete degradation after 12 weeks. A cell-rich reconstruction zone formed during degradation, which was subsequently replaced by new bone. The degradation rate of the scaffolds corresponded closely to bone regeneration. Notably, the Mg3d and Mg275d scaffolds supported the faster formation of mature lamellar bone compared to the TCP scaffolds. These results indicate that magnesium phosphate (MgP)-based scaffolds represent a promising alternative to conventional calcium phosphate (CP)-based bone substitutes, given their rapid and almost complete degradation and their effective support of bone regeneration.

Schlagwörter

Stichwörter der Autor:innen

3D powder printingbone cementsdegradable bone substitutesfarringtoniteosteoregenerationscaffoldstanfielditestruvite

Autor:innen und Institutionen

  • Clinic for Small Animal Surgery and Reproduction, Ludwig Maximilians University Munich, 80539 Munich, Germany.
  • Department for Functional Materials in Medicine and Dentistry, University of Wuerzburg, 97070 Wuerzburg, Germany.

ORCID-Profile: Andrea Meyer-Lindenberg

Förderung

  • Deutsche Forschungsgemeinschaft
  • German Research Foundation

Zitieren

APA

Hiepe, S., Vorndran, E., Feichtner, F., Waselau, A. C., & Meyer-Lindenberg, A. (2025). In Vivo Degradation Behaviour and Osteoregenerative Capacity of 3D-Printed Magnesium Phosphate and Calcium Magnesium Phosphate Cement Scaffolds. Materials, 18(22), 5067. https://doi.org/10.3390/ma18225067

Vancouver

Hiepe S, Vorndran E, Feichtner F, Waselau AC, Meyer-Lindenberg A. In Vivo Degradation Behaviour and Osteoregenerative Capacity of 3D-Printed Magnesium Phosphate and Calcium Magnesium Phosphate Cement Scaffolds. Materials. 2025;18(22):5067. doi:10.3390/ma18225067

BibTeX
@article{Hiepe2025,
  author = {Hiepe, Sophia and Vorndran, Elke and Feichtner, Franziska and Waselau, Anja-Christina and Meyer-Lindenberg, Andrea},
  title = {In Vivo Degradation Behaviour and Osteoregenerative Capacity of 3D-Printed Magnesium Phosphate and Calcium Magnesium Phosphate Cement Scaffolds},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {22},
  pages = {5067},
  doi = {10.3390/ma18225067}
}
Kostenlos starten →