EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Adding Molybdenum on Microstructure, Hardness, and Corrosion Resistance of an AlCoCrFeNiMo0.25 High-Entropy Alloy

Mariusz Walczak iD, Wojciech J Nowak iD, Wojciech Okuniewski iD, Dariusz Chocyk iD

Materials · 30.09.2025 · 18 (19) · 4566

DOI: 10.3390/ma18194566 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 30.09.2025. Verfasst von Mariusz Walczak und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Engineering, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36D, 20-618 Lublin, Poland. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 62 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Polish Minister of Education and Science.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Recent literature reports have shown that individual HEAs, especially those of the AlCoCrFeNi composition system alloyed with appropriately selected elements, exhibit excellent mechanical properties and corrosion resistance, making them promising candidates for replacing conventional materials such as austenitic steels in corrosive environments. Therefore, in the present study, the high-entropy alloy AlCoCrFeNiMo0.25 was examined and compared with AISI 304L steel and the reference alloy AlCoCrFeNi. The HEA was produced by arc melting in vacuum. The effect of molybdenum addition (5% at.) on the structure, mechanical properties, and corrosion resistance was evaluated. Potentiodynamic polarization and electrochemical impedance spectroscopy tests were carried out in a 3.5% NaCl solution in a three-electrode electrochemical system. The addition of molybdenum to AlCoCrFeNiMox alloy additionally caused, along with the BCC phase, the formation of σ phase and FCC phase (less than 1%), as well as changes in the microstructure, leading to the fragmentation of grains and the formation of a mosaic structure. On the basis of nanoindentation tests, it was established that the addition of Mo increases hardness and elastic modulus and improves nanoindentation coefficients H/E and H3/E2, as well as an increase in the elastic recovery index while decreasing plasticity index (vs. the reference equiatomic HEA). This indicates the improvement of anti-wear properties with impact loading resistance. In turn, electrochemical tests have shown that the addition of Mo improves corrosion resistance. Corrosion pitting develops in Al- and Ni-rich areas of HEA alloys, as a result of galvanic microcorrosion related to Cr chemical segregation. In general, the addition of 5% Mo results in a fine-grained mosaic structure, which primarily translates into favorable nanoindentation and corrosion properties of the AlCoCrFeNiMo0.25 alloy.

Schlagwörter

Stichwörter der Autor:innen

Mo effectcorrosion resistancehigh-entropy alloysnanoindentation

Autor:innen und Institutionen

  • Department of Materials Engineering, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36D, 20-618 Lublin, Poland.
  • Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, Powstanców Warszawy 12, 35-959 Rzeszów, Poland.
  • Department of Applied Physics, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36D, 20-618 Lublin, Poland.

ORCID-Profile: Mariusz Walczak, Wojciech J Nowak, Wojciech Okuniewski, Dariusz Chocyk

Förderung

  • Polish Minister of Education and Science

Zitieren

APA

Walczak, M., Nowak, W. J., Okuniewski, W., & Chocyk, D. (2025). Effect of Adding Molybdenum on Microstructure, Hardness, and Corrosion Resistance of an AlCoCrFeNiMo0.25 High-Entropy Alloy. Materials, 18(19), 4566. https://doi.org/10.3390/ma18194566

Vancouver

Walczak M, Nowak WJ, Okuniewski W, Chocyk D. Effect of Adding Molybdenum on Microstructure, Hardness, and Corrosion Resistance of an AlCoCrFeNiMo0.25 High-Entropy Alloy. Materials. 2025;18(19):4566. doi:10.3390/ma18194566

BibTeX
@article{Walczak2025,
  author = {Walczak, Mariusz and Nowak, Wojciech J and Okuniewski, Wojciech and Chocyk, Dariusz},
  title = {Effect of Adding Molybdenum on Microstructure, Hardness, and Corrosion Resistance of an AlCoCrFeNiMo0.25 High-Entropy Alloy},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {19},
  pages = {4566},
  doi = {10.3390/ma18194566}
}
Kostenlos starten →