EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Abrasive Waterjet Machining of r-GO Infused Mg Fiber Metal Laminates: ANFIS Modelling and Optimization Through Antlion Optimizer Algorithm

Devaraj Rajamani iD, Mahalingam Siva Kumar iD, Arulvalavan Tamilarasan iD

Materials · 25.09.2025 · 18 (19) · 4480

DOI: 10.3390/ma18194480 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 25.09.2025. Verfasst von Devaraj Rajamani und 2 weiteren Autor:innen. Beteiligte Einrichtung: Centre for Advanced Materials Processing, Department of Mechanical Engineering, Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Techn…. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Chennai, India.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This research proposes an intelligent modeling and optimization strategy for abrasive waterjet machining (AWJM) of magnesium-based fiber metal laminates (FMLs) reinforced with reduced graphene oxide (r-GO). Experiments were designed using the Box–Behnken method, considering waterjet pressure, stand-off distance, traverse speed, and r-GO content as inputs, while kerf taper (Kt), surface roughness (Ra), and material removal rate (MRR) were evaluated as outputs. Adaptive Neuro-Fuzzy Inference System (ANFIS) models were developed for each response, with their critical optimized hyperparameters such as cluster radius, quash factor, and training data split through the dragonfly optimization (DFO) algorithm. The optimized ANFIS networks yielded a high predictive accuracy, with low RMSE and MAPE values and close agreement between predicted and measured results. Four metaheuristic algorithms including particle swarm optimization (PSO), salp swarm optimization (SSO), whale optimization algorithm (WOA), and the antlion optimizer (ALO) were applied for simultaneous optimization, using a TOPSIS-based single-objective formulation. ALO outperformed the others, identifying 325 MPa waterjet pressure, 2.5 mm stand-off, 800 mm/min traverse speed, and 0.00602 wt% r-GO addition in FMLs as optimal conditions. These settings produced a kerf taper of 2.595°, surface roughness of 8.9897 µm, and material removal rate of 138.13 g/min. The proposed ANFIS-ALO framework demonstrates strong potential for achieving precision and productivity in AWJM of hybrid laminates.

Schlagwörter

Stichwörter der Autor:innen

ANFISabrasive waterjet machiningantlion algorithmfiber metal laminatesintelligent modelingoptimization

Autor:innen und Institutionen

  • Centre for Advanced Materials Processing, Department of Mechanical Engineering, Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Chennai 600062, India.
  • Department of Mechanical Engineering, SRM TRP Engineering College, Tiruchirappalli 621105, India.
  • Department of Artificial Intelligence and Data Science, Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences (SIMATS), Chennai 602105, India.

ORCID-Profile: Devaraj Rajamani, Mahalingam Siva Kumar, Arulvalavan Tamilarasan

Förderung

  • Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Chennai, India

Zitieren

APA

Rajamani, D., Siva Kumar, M., & Tamilarasan, A. (2025). Abrasive Waterjet Machining of r-GO Infused Mg Fiber Metal Laminates: ANFIS Modelling and Optimization Through Antlion Optimizer Algorithm. Materials, 18(19), 4480. https://doi.org/10.3390/ma18194480

Vancouver

Rajamani D, Siva Kumar M, Tamilarasan A. Abrasive Waterjet Machining of r-GO Infused Mg Fiber Metal Laminates: ANFIS Modelling and Optimization Through Antlion Optimizer Algorithm. Materials. 2025;18(19):4480. doi:10.3390/ma18194480

BibTeX
@article{Rajamani2025,
  author = {Rajamani, Devaraj and Siva Kumar, Mahalingam and Tamilarasan, Arulvalavan},
  title = {Abrasive Waterjet Machining of r-GO Infused Mg Fiber Metal Laminates: ANFIS Modelling and Optimization Through Antlion Optimizer Algorithm},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {19},
  pages = {4480},
  doi = {10.3390/ma18194480}
}
Kostenlos starten →