EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fatigue Performance of Nitrided H13 Tool Steel Pre-Treated with Fine Particle Peening

Hung-Chi Lee, Tai-Cheng Chen iD, Wen-Han Chen iD, Leu-Wen Tsay iD

Materials · 02.09.2025 · 18 (17) · 4121

DOI: 10.3390/ma18174121 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 02.09.2025. Verfasst von Hung-Chi Lee und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Optoelectronics and Materials Technology, National Taiwan Ocean University, Keelung 202301, Taiwan. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science and Technology Council.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluated the fatigue performance of nitrided H13 steel with and without a compound layer (CL), using two nitrogen potentials (KN = 0.8, designated as LN, and KN = 2.0, designated as HN). Fine particle peening (FPP) was applied prior to gas nitriding to introduce a refined microstructure and compressive residual stress (CRS) in the peened zone. After gas nitriding at 540 °C for 8 h, the refined structure remained on the outermost layer of all samples, regardless of the nitrogen potential. A CL primarily composed of Fe3N formed on the external surface of the HN sample, whereas the LN sample remained free of CL. A higher KN promoted CL formation and slightly increased the case depth in the HN sample compared to the LN sample. Fatigue cracks initiated at the external surface of the H13 steel substrate (SB). Overall, the LN and HN samples exhibited similar residual stress fields and, consequently, comparable fatigue performance. In the high-cycle fatigue regime, fatigue cracks originated from subsurface inclusions, resulting in significantly improved fatigue strength and life for both the LN and HN samples compared to the SB sample. Under cyclic stresses at or above 1100 MPa, the crack initiation site in the HN sample tended to shift from subsurface inclusions to the external surface. Throughout the fatigue tests, no multi-cracking or spalling of the CL was observed in the HN sample, regardless of the cyclic stress.

Schlagwörter

Stichwörter der Autor:innen

AISI H13fine particle peeninggas nitridingrotating bending fatiguesubsurface crack initiation

Autor:innen und Institutionen

  • Department of Optoelectronics and Materials Technology, National Taiwan Ocean University, Keelung 202301, Taiwan.
  • Department of Material Research, National Atomic Research Institute, Taoyuan 325207, Taiwan.
  • Neutron Scattering Division, Oak Ridge National Laboratory, Oak Ridge, TN 37830, USA.
  • Vincent Vacuum-Tech Co., Ltd., Taoyuan 326019, Taiwan.

ORCID-Profile: Tai-Cheng Chen, Wen-Han Chen, Leu-Wen Tsay

Förderung

  • National Science and Technology Council

Zitieren

APA

Lee, H. C., Chen, T. C., Chen, W. H., & Tsay, L. W. (2025). Fatigue Performance of Nitrided H13 Tool Steel Pre-Treated with Fine Particle Peening. Materials, 18(17), 4121. https://doi.org/10.3390/ma18174121

Vancouver

Lee HC, Chen TC, Chen WH, Tsay LW. Fatigue Performance of Nitrided H13 Tool Steel Pre-Treated with Fine Particle Peening. Materials. 2025;18(17):4121. doi:10.3390/ma18174121

BibTeX
@article{Lee2025,
  author = {Lee, Hung-Chi and Chen, Tai-Cheng and Chen, Wen-Han and Tsay, Leu-Wen},
  title = {Fatigue Performance of Nitrided H13 Tool Steel Pre-Treated with Fine Particle Peening},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {17},
  pages = {4121},
  doi = {10.3390/ma18174121}
}
Kostenlos starten →