EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative Analysis of Microstructure and Properties of Wear-Resistant Structural Steels

Helena Lukšić, Tomislav Rodinger iD, Vera Rede iD, Zrinka Švagelj, Danko Ćorić iD

Materials · 27.08.2025 · 18 (17) · 4002

DOI: 10.3390/ma18174002 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.08.2025. Verfasst von Helena Lukšić und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials, Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, 10000 Zagreb, Croatia. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper presents the results of wear tests of two types of commercial low-carbon, low-alloy martensitic abrasion-resistant steels, Hardox 450 and XAR 450, which belong to the hardness class 450 HBW. These steels, due to their increased resistance to the abrasive wear mechanism, are used for machine parts for applications in intensive abrasion environments such as construction, mining, and agriculture. The scope of work included microstructure analysis on an optical microscope, chemical composition analysis, Vickers hardness measurements at different loads (HV0.2, HV1 and HV2), and wear testing. Wear tests were carried out by the standard method “dry sand—rubber wheel”, and tests on the Taber abrader device. Microstructure analysis revealed that both steels have a similar non-oriented, homogenous, fine-grained martensitic microstructure. The results of HV2 hardness measurements showed a similar trend for both steels in all examined sections of the plates. For both tested steels, the hardness values of HV0.2 and HV1 are slightly higher than HV2, but the scattering of the results is also greater. Abrasion resistance testing using the standard “dry sand—rubber wheel” method showed that Hardox 450 steel has a lower volume loss of about 8%, but a greater scattering of the results compared to XAR 450 steel. The results of the abrasion resistance test on the Taber abrader device confirmed approximately the same behavior. For both steels, a prediction model was established for a reliable assessment of the wear intensity concerning the grain size. Although examined steels belong to the same hardness class, Hardox steel seems to be a more appropriate choice for the manufacture of machine components exposed to abrasive wear.

Schlagwörter

Stichwörter der Autor:innen

Hardox 450XAR 450abrasive wear resistancehardnessmicrostructure

Autor:innen und Institutionen

  • Department of Materials, Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, 10000 Zagreb, Croatia.

ORCID-Profile: Tomislav Rodinger, Vera Rede, Danko Ćorić

Zitieren

APA

Lukšić, H., Rodinger, T., Rede, V., Švagelj, Z., & Ćorić, D. (2025). Comparative Analysis of Microstructure and Properties of Wear-Resistant Structural Steels. Materials, 18(17), 4002. https://doi.org/10.3390/ma18174002

Vancouver

Lukšić H, Rodinger T, Rede V, Švagelj Z, Ćorić D. Comparative Analysis of Microstructure and Properties of Wear-Resistant Structural Steels. Materials. 2025;18(17):4002. doi:10.3390/ma18174002

BibTeX
@article{Luki2025,
  author = {Lukšić, Helena and Rodinger, Tomislav and Rede, Vera and Švagelj, Zrinka and Ćorić, Danko},
  title = {Comparative Analysis of Microstructure and Properties of Wear-Resistant Structural Steels},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {17},
  pages = {4002},
  doi = {10.3390/ma18174002}
}
Kostenlos starten →