EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Research on the Process of Cutting Nonwoven Materials Using Surgical Gauze as an Example

Marcin Zastempowski iD, Andrzej Bochat iD, Maciej Janiec iD

Materials · 27.06.2025 · 18 (13) · 3049

DOI: 10.3390/ma18133049 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 27.06.2025. Verfasst von Marcin Zastempowski und 2 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, Bydgoszcz University of Science and Technology, Al. Prof. S. Kaliskiego 7, 85-796 Bydgoszcz, Poland. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Minister of Science and Higher Education.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The aim of this study was to examine the functional characteristics of the process of cutting surgical gauze with a drum cutting unit. For this purpose, the authors designed and constructed a test stand on which experimental tests were conducted. As part of this study, the results of the experimental tests are presented, which were conducted for three selected thicknesses of surgical gauze samples, four selected angles of feeding of the material to be cut and nine selected cutting speeds. In order to determine cutting resistance, the specific cutting resistance was used, and the energy consumption was estimated using the specific cutting work related to the cutting surface of the surgical gauze. The conducted experimental studies demonstrated that the highest value of the specific cutting resistance pc=78.14 N⋅m−1 occurred during the cutting of eight-layer gauze at a cutting angle α=0° and a cutting speed Vc=0.66 m⋅s−1. Meanwhile, the highest value of the specific cutting work was approximately LjS=120.00 J⋅m−2 during the cutting of three-layer gauze, also at a cutting speed Vc=0.66 m⋅s−1 for cutting angles α=0° and α=5°. This study found that Vc=0.66 m⋅s−1 is the threshold cutting speed at which the material is cut. Below this speed, the cutting drum does not have enough momentum to cut the material. Based on the statistical analysis of the obtained test results, it was concluded that there exists a relationship between the independent and dependent variables. The cutting speed has the greatest impact on the parameters of the surgical gauze cutting process. The test results, which have not been found in the worldwide literature to date, constitute a valuable contribution to the development of the theory of surgical gauze cutting. The experimentally determined specific cutting resistance pc and specific cutting work of surgical gauze broaden the knowledge of the materials used in medicine and contribute to the expansion of scientific knowledge in this field.

Schlagwörter

Stichwörter der Autor:innen

cuttingdrum cutting unitsurgical gauzeunit cutting resistanceunit cutting work

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, Bydgoszcz University of Science and Technology, Al. Prof. S. Kaliskiego 7, 85-796 Bydgoszcz, Poland.
  • SORIMEX sp. z o.o., ul. Równinna 25, 87-100 Toruń, Poland.

ORCID-Profile: Marcin Zastempowski, Andrzej Bochat, Maciej Janiec

Förderung

  • Minister of Science and Higher Education

Zitieren

APA

Zastempowski, M., Bochat, A., & Janiec, M. (2025). Research on the Process of Cutting Nonwoven Materials Using Surgical Gauze as an Example. Materials, 18(13), 3049. https://doi.org/10.3390/ma18133049

Vancouver

Zastempowski M, Bochat A, Janiec M. Research on the Process of Cutting Nonwoven Materials Using Surgical Gauze as an Example. Materials. 2025;18(13):3049. doi:10.3390/ma18133049

BibTeX
@article{Zastempowski2025,
  author = {Zastempowski, Marcin and Bochat, Andrzej and Janiec, Maciej},
  title = {Research on the Process of Cutting Nonwoven Materials Using Surgical Gauze as an Example},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {13},
  pages = {3049},
  doi = {10.3390/ma18133049}
}
Kostenlos starten →