EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Printing Orientation on the Flexural Strength of Different Light-Cured Resins Manufactured with Two 3D Printers: In Vitro Study

Maria Francesca Sfondrini iD, Federica Gariboldi iD, Michael Cerri, Claudia Todaro iD, Maurizio Pascadopoli iD, Giulia Casiraghi, Andrea Scribante iD

Materials · 26.06.2025 · 18 (13) · 3029

DOI: 10.3390/ma18133029 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 26.06.2025. Verfasst von Maria Francesca Sfondrini und 6 weiteren Autor:innen. Beteiligte Einrichtung: Unit of Orthodontics and Pediatric Dentistry, Section of Dentistry, Department of Clinical, Surgical, Diagnostic and Pediatric Sciences, University o…. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Three-dimensional printing is rapidly growing in applied dentistry. In order to print faster, increase workflow, and minimize the consumption of resin material, it is important to use the right printer and the correct printing orientation. The objective of the present report is to analyze the flexural strength of specimens realized with two different dental light-curing resins (Keyguide and C&B) obtained from two different Digital Light Processing (DLP) 3D printers. Different printing orientations (0°, 45°, and 90°) were evaluated. 3D Builder, MeshMixer, RayWare, and Chitubox software were used to design the resin specimens. A total of 15 Keyguide and 15 C&B specimens in the shape of a rectangular parallelepiped, with dimensions of 2 mm × 2 mm × 25 mm, were obtained with the Sprintray Moonray S 3D printer, and the 15 Keyguide and 15 C&B specimens presented the same characteristics as those printed using the Moon Night printer. Prior to sample printing, a calibration protocol (tolerance test and dimensional accuracy test) was performed using RayWare software. This procedure allowed compensation for resin shrinkage or expansion, thus ensuring dimensional consistency in all printed samples. Each resin specimen, after printing and post-processing (MoonWash 2 and MoonLight 2), was subjected to a mechanical test with a universal testing machine. After breaking the specimen, the flexural strength values were recorded with computer software (Bluehill, Instron Corporation, Canton, MA, USA). According to the results obtained, the printing orientation of the specimens does not affect the flexural strength of the two materials examined. However, at the maximum load, some differences emerged for both materials printed with the Moon Night printer, depending on their build angle. Both light-cured resins tested had a higher maximum load resistance when printed with the newer Moon Night printer. This result could be due to the Moon Night printer’s better construction characteristics compared to those of the Sprintray or to issues related to the dimensional calibration of the specimens.

Schlagwörter

Stichwörter der Autor:innen

3D printingflexural strengthorientationprinterresinsoftwaresupports

Autor:innen und Institutionen

  • Unit of Orthodontics and Pediatric Dentistry, Section of Dentistry, Department of Clinical, Surgical, Diagnostic and Pediatric Sciences, University of Pavia, 27100 Pavia, Italy.
  • Private Practice, 29011 Borgonovo Val Tidone, Italy.
  • Unit of Dental Hygiene, Section of Dentistry, Department of Clinical, Surgical, Diagnostic and Pediatric Sciences, University of Pavia, 27100 Pavia, Italy.

ORCID-Profile: Maria Francesca Sfondrini, Federica Gariboldi, Claudia Todaro, Maurizio Pascadopoli, Andrea Scribante

Zitieren

APA

Sfondrini, M. F., Gariboldi, F., Cerri, M., Todaro, C., Pascadopoli, M., Casiraghi, G., & Scribante, A. (2025). Influence of Printing Orientation on the Flexural Strength of Different Light-Cured Resins Manufactured with Two 3D Printers: In Vitro Study. Materials, 18(13), 3029. https://doi.org/10.3390/ma18133029

Vancouver

Sfondrini MF, Gariboldi F, Cerri M, Todaro C, Pascadopoli M, Casiraghi G, et al. Influence of Printing Orientation on the Flexural Strength of Different Light-Cured Resins Manufactured with Two 3D Printers: In Vitro Study. Materials. 2025;18(13):3029. doi:10.3390/ma18133029

BibTeX
@article{Sfondrini2025,
  author = {Sfondrini, Maria Francesca and Gariboldi, Federica and Cerri, Michael and Todaro, Claudia and Pascadopoli, Maurizio and Casiraghi, Giulia and Scribante, Andrea},
  title = {Influence of Printing Orientation on the Flexural Strength of Different Light-Cured Resins Manufactured with Two 3D Printers: In Vitro Study},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {13},
  pages = {3029},
  doi = {10.3390/ma18133029}
}
Kostenlos starten →