EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Zr on Al-Ti-B-Based Grain Refiners in AlSiMgCuZr Alloy

Dawid Kapinos iD, Bogusław Augustyn iD, Sonia Boczkal, Kamila Limanówka iD, Bartłomiej Płonka iD, Aldona Garbacz-Klempka iD, Marcin Piękoś iD, Janusz Kozana iD

Materials · 24.06.2025 · 18 (13) · 3000

DOI: 10.3390/ma18133000 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 24.06.2025. Verfasst von Dawid Kapinos und 7 weiteren Autor:innen. Beteiligte Einrichtung: Łukasiewicz Research Network-Institute of Non-Ferrous Metals, Light Metals Centre, Piłsudskiego 19, 32-050 Skawina, Poland. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The National Centre for Research and Development, Polish Ministry of Science and Higher Education.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

One of the most effective methods of improving the properties of aluminium alloys is grain refining using Al-Ti-B master alloys. In contrast, zirconium is a key alloying element, used mainly in 2xxx and 7xxx series aluminium alloys, where it contributes to dispersion enhancement and reduces the rate of dynamic recrystallisation. However, even trace amounts of zirconium—just a few hundredths of ppm—significantly reduce the performance of Al-Ti-B grain refiners, a phenomenon known as ‘Zr poisoning’. This study investigates the impact of holding time and the level of Al-5Ti-1B addition on the microstructure and properties of an AlMgSi(Cu) alloy containing 0.15 wt.% Zr, cast as 7-inch DC billets. The structure and phase distribution were characterised using optical microscopy (OM), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), and transmission electron microscopy (TEM). Grain size and morphology were evaluated through macrostructure analysis (etched cross-sections and polarised light microscopy), while chemical and elemental distributions were analysed via SEM-EDS and STEM-EDS mapping. Additionally, Brinell hardness measurements were conducted across the billet diameter to assess the correlation between grain size and mechanical properties. The results show that reducing holding time and increasing the Al-5Ti-1B addition improves grain refinement efficiency despite the presence of Zr. The finest grain structure (150–170 μm) and most homogeneous hardness distribution were achieved when the grain refiner was continuously fed during casting at 80 ppm B. These findings are supported by the literature and contribute to a deeper understanding of the Zr poisoning effect and its mitigation through optimized casting practice.

Schlagwörter

Stichwörter der Autor:innen

AlSiMgCuZr alloysZr poisoningaluminium alloysgrain refinement

Autor:innen und Institutionen

  • Łukasiewicz Research Network-Institute of Non-Ferrous Metals, Light Metals Centre, Piłsudskiego 19, 32-050 Skawina, Poland.
  • Faculty of Foundry Engineering, AGH University of Krakow, Reymonta 23, 30-059 Cracow, Poland.

ORCID-Profile: Dawid Kapinos, Bogusław Augustyn, Kamila Limanówka, Bartłomiej Płonka, Aldona Garbacz-Klempka, Marcin Piękoś, Janusz Kozana

Förderung

  • The National Centre for Research and Development
  • Polish Ministry of Science and Higher Education

Zitieren

APA

Kapinos, D., Augustyn, B., Boczkal, S., Limanówka, K., Płonka, B., Garbacz-Klempka, A., Piękoś, M., & Kozana, J. (2025). Influence of Zr on Al-Ti-B-Based Grain Refiners in AlSiMgCuZr Alloy. Materials, 18(13), 3000. https://doi.org/10.3390/ma18133000

Vancouver

Kapinos D, Augustyn B, Boczkal S, Limanówka K, Płonka B, Garbacz-Klempka A, et al. Influence of Zr on Al-Ti-B-Based Grain Refiners in AlSiMgCuZr Alloy. Materials. 2025;18(13):3000. doi:10.3390/ma18133000

BibTeX
@article{Kapinos2025,
  author = {Kapinos, Dawid and Augustyn, Bogusław and Boczkal, Sonia and Limanówka, Kamila and Płonka, Bartłomiej and Garbacz-Klempka, Aldona and Piękoś, Marcin and Kozana, Janusz},
  title = {Influence of Zr on Al-Ti-B-Based Grain Refiners in AlSiMgCuZr Alloy},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {13},
  pages = {3000},
  doi = {10.3390/ma18133000}
}
Kostenlos starten →