EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Post-Printing Polymerization Time on the Elution of Residual Monomers and Water Sorption of 3D-Printed Resin Composite

Shaima Alharbi, Abdulrahman Alshabib iD, Hamad Algamaiah, Muath Aldosari iD, Abdullah Alayad iD

Materials · 19.06.2025 · 18 (12) · 2905

DOI: 10.3390/ma18122905 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 19.06.2025. Verfasst von Shaima Alharbi und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dental Science, College of Dentistry, King Saud University, Riyadh 11362, Saudi Arabia. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 45 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluated the effect of post-printing polymerization time on residual monomer elution and water sorption in a 3D-printed resin composite. Eighty samples were fabricated and assigned to four groups based on post-curing duration: 0, 20, 40, and 60 min. Each group was subdivided according to two storage conditions (distilled water and 75% ethanol–water solution), and evaluated at 1 and 7 days. High-performance liquid chromatography (HPLC) quantified eluted monomers. Additionally, 40 specimens underwent a 4-month sorption/desorption cycle for water sorption and solubility assessment. Data were statistically analyzed using kernel regression (monomer data) and Welch ANOVA (water sorption and solubility) at a significance level of p < 0.05. BisEMA was the only monomer detected, with significantly higher elution recorded in ethanol-based storage. Increasing post-curing time notably reduced both monomer release and water sorption/solubility (p < 0.001); however, the optimal results were observed at 40 min post-curing. These findings suggest that extending post-curing beyond an optimal threshold does not further improve composite properties, underscoring the importance of identifying precise curing parameters in order to enhance durability and material performance.

Schlagwörter

Stichwörter der Autor:innen

3D resin compositeHPLCmonomer elutionmonomer releasepost-curing timewater sorption

Autor:innen und Institutionen

  • Department of Restorative Dental Science, College of Dentistry, King Saud University, Riyadh 11362, Saudi Arabia.
  • Department of Conservative Dentistry, College of Dentistry, Aljouf University, Sakaka 72388, Saudi Arabia.
  • Periodontics and Community Dentistry, College of Dentistry, King Saud University, Riyadh 11362, Saudi Arabia.
  • Oral Health Policy and Epidemiology, Harvard School of Dental Medicine, Boston, MA 02115, USA.

ORCID-Profile: Abdulrahman Alshabib, Muath Aldosari, Abdullah Alayad

Zitieren

APA

Alharbi, S., Alshabib, A., Algamaiah, H., Aldosari, M., & Alayad, A. (2025). Influence of Post-Printing Polymerization Time on the Elution of Residual Monomers and Water Sorption of 3D-Printed Resin Composite. Materials, 18(12), 2905. https://doi.org/10.3390/ma18122905

Vancouver

Alharbi S, Alshabib A, Algamaiah H, Aldosari M, Alayad A. Influence of Post-Printing Polymerization Time on the Elution of Residual Monomers and Water Sorption of 3D-Printed Resin Composite. Materials. 2025;18(12):2905. doi:10.3390/ma18122905

BibTeX
@article{Alharbi2025,
  author = {Alharbi, Shaima and Alshabib, Abdulrahman and Algamaiah, Hamad and Aldosari, Muath and Alayad, Abdullah},
  title = {Influence of Post-Printing Polymerization Time on the Elution of Residual Monomers and Water Sorption of 3D-Printed Resin Composite},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {12},
  pages = {2905},
  doi = {10.3390/ma18122905}
}
Kostenlos starten →