EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Heat Treatment on Microstructure and Tensile Property of Laser-Powder-Bed-Melted Al–Mn–Mg–Sc–Zr Alloy

Zhiqiang Cao, Hui Yin, Jin Jiang, Mingliang Cui, Hao Zhang, Sheng Cao iD

Materials · 03.04.2025 · 18 (7) · 1638

DOI: 10.3390/ma18071638 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 03.04.2025. Verfasst von Zhiqiang Cao und 5 weiteren Autor:innen. Beteiligte Einrichtung: Center for Instrumental Analysis, University of Shanghai for Science and Technology, 516 Jungong Road, Shanghai 200093, China. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the National Key R&D Program of China, the National Key R&D Program of China, the Key R&D Project of Sichuan Provincial Science and Technology Program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study explored the effects of T5 and T6 heat treatments on the microstructure and tensile properties of a laser powder bed fusion (LPBF)-fabricated Al–Mn–Mg–Sc–Zr alloy. The as-built condition exhibited a bi-modal grain structure of equiaxed and columnar grains. Specimens after T5 heat treatment also had a bi-modal microstructure with slight grain growth and the precipitation of secondary Al3Sc, which enhanced the yield strength via precipitation hardening but reduced ductility. In contrast, T6 treatment triggered recrystallization, and the microstructure was only coarse equiaxed α-Al grains. This microstructure change was accompanied by coarsened primary Al3X and Al6(Mn, Fe) precipitates, partial Mg2Si dissolution, and significant secondary Al3Sc particle growth. Consequently, T6-treated specimens showed lower strength than their T5 counterparts and the poorest ductility due to brittle fracture induced by the stress concentration effect of coarse precipitates at grain boundaries.

Schlagwörter

Stichwörter der Autor:innen

Al–Mn–Mg–Sc–Zr alloyheat treatmentlaser powder bed fusionmechanical property

Autor:innen und Institutionen

  • Center for Instrumental Analysis, University of Shanghai for Science and Technology, 516 Jungong Road, Shanghai 200093, China.
  • Deyang Wanhang Die Forging Co., Ltd., China National Erzhong Group Co., Deyang 618000, China.
  • China State Shipbuilding Co., Ltd., Huangpu Wenchong Shipbuilding Company Ltd., Guangzhou 510715, China.
  • College of Materials Science and Engineering, Beijing University of Technology, Beijing 100080, China.
  • Institute of Advanced Wear & Corrosion Resistant and Functional Materials, Jinan University, Guangzhou 510632, China.
  • College of Chemistry and Materials Science, Jinan University, Guangzhou 511443, China.

ORCID-Profile: Sheng Cao

Förderung

  • the National Key R&D Program of China
  • the National Key R&D Program of China
  • the Key R&D Project of Sichuan Provincial Science and Technology Program
  • the National Natural Science Foundation of China
  • the Guangzhou Fundamental Research Program

Zitieren

APA

Cao, Z., Yin, H., Jiang, J., Cui, M., Zhang, H., & Cao, S. (2025). Effect of Heat Treatment on Microstructure and Tensile Property of Laser-Powder-Bed-Melted Al–Mn–Mg–Sc–Zr Alloy. Materials, 18(7), 1638. https://doi.org/10.3390/ma18071638

Vancouver

Cao Z, Yin H, Jiang J, Cui M, Zhang H, Cao S. Effect of Heat Treatment on Microstructure and Tensile Property of Laser-Powder-Bed-Melted Al–Mn–Mg–Sc–Zr Alloy. Materials. 2025;18(7):1638. doi:10.3390/ma18071638

BibTeX
@article{Cao2025,
  author = {Cao, Zhiqiang and Yin, Hui and Jiang, Jin and Cui, Mingliang and Zhang, Hao and Cao, Sheng},
  title = {Effect of Heat Treatment on Microstructure and Tensile Property of Laser-Powder-Bed-Melted Al–Mn–Mg–Sc–Zr Alloy},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {7},
  pages = {1638},
  doi = {10.3390/ma18071638}
}
Kostenlos starten →