EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Three-Dimensional Printing of Rigid–Flexible Ceramic–Epoxy Composites with Excellent Mechanical Properties

Zhaozhi Wang, Biao Jiang, Yajie Liu iD, Zhiheng Xin, Zhibin Jiao

Materials · 26.03.2025 · 18 (7) · 1479

DOI: 10.3390/ma18071479 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 26.03.2025. Verfasst von Zhaozhi Wang und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Shenyang University of Technology, Shenyang 110870, China. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Wang zhaozhi, The Liaoning Provincial Science and Technology Program Joint Fund.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Inspired by the Bouligand structure of the mantis shrimp’s dactyl club, in this study, we employed direct ink writing 3D printing technology to fabricate bioinspired gradient ceramic samples with varying gradient spacings and rotation angles. A rigid–flexible coupled bioinspired gradient ceramic–epoxy resin composite was successfully constructed based on epoxy resin infiltration. The effects of gradient variations and rotation angles on mechanical properties were systematically investigated with flexural strength and fracture toughness tests. The experimental results revealed that, at a fixed rotation angle, both the flexural strength and fracture toughness initially increased and then decreased with an increase in gradient spacing. The infiltration of epoxy resin significantly enhanced the mechanical performance of the composite samples. Specifically, the maximum flexural strength of 63.35 MPa was achieved at Δd = 0.08 and a rotation angle of 12°, while the highest fracture toughness of 2 MPa/m2 was observed at Δd = 0.1 and a rotation angle of 12°. A failure analysis indicated that the introduction of gradient structures and epoxy resin infiltration altered the failure forms of traditional ceramics, with the primary toughening mechanisms including crack deflection, fiber pull-out, and crack branching. In this study, we successfully developed a rigid–flexible coupled bioinspired gradient ceramic–epoxy resin composite with excellent mechanical properties based on bioinspired design and gradient optimization, providing new insights and methodologies for the design and fabrication of high-performance ceramic materials.

Schlagwörter

Stichwörter der Autor:innen

3D printingbiomimetic gradient structureceramic–epoxy dual-phase compositesflexural strengthfracture toughnessrigid–flexible composites

Autor:innen und Institutionen

  • School of Mechanical Engineering, Shenyang University of Technology, Shenyang 110870, China.

ORCID-Profile: Yajie Liu

Förderung

  • Wang zhaozhi
  • The Liaoning Provincial Science and Technology Program Joint Fund

Zitieren

APA

Wang, Z., Jiang, B., Liu, Y., Xin, Z., & Jiao, Z. (2025). Three-Dimensional Printing of Rigid–Flexible Ceramic–Epoxy Composites with Excellent Mechanical Properties. Materials, 18(7), 1479. https://doi.org/10.3390/ma18071479

Vancouver

Wang Z, Jiang B, Liu Y, Xin Z, Jiao Z. Three-Dimensional Printing of Rigid–Flexible Ceramic–Epoxy Composites with Excellent Mechanical Properties. Materials. 2025;18(7):1479. doi:10.3390/ma18071479

BibTeX
@article{Wang2025,
  author = {Wang, Zhaozhi and Jiang, Biao and Liu, Yajie and Xin, Zhiheng and Jiao, Zhibin},
  title = {Three-Dimensional Printing of Rigid–Flexible Ceramic–Epoxy Composites with Excellent Mechanical Properties},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {7},
  pages = {1479},
  doi = {10.3390/ma18071479}
}
Kostenlos starten →