EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Preparation and Properties of PETG Filament Modified with a Metallic Additive

Piotr Zmuda Trzebiatowski iD, Tomasz Królikowski iD, Agnieszka Ubowska iD, Katarzyna Wilpiszewska iD

Materials · 07.03.2025 · 18 (6) · 1203

DOI: 10.3390/ma18061203 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 07.03.2025. Verfasst von Piotr Zmuda Trzebiatowski und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Mechanical Engineering, Koszalin University of Technology, ul. Śniadeckich 2, 75-453 Koszalin, Poland. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Narodowa Agencja Wymiany Akademickiej, National Agency for Academic Exchange (NAWA), the project “Koszalin University of Technology as an active member of EU4Dual”,.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The materials used as filaments for additive techniques should exhibit various properties depending on the application and the requirements. The motivation for this study was the need to obtain a filament exhibiting appropriate aesthetic (metal-like) and mechanical properties. Glycol-modified poly(ethylene terephthalate) copolymer (PETG) and micrometric steel powder were used for composite preparation. Subsequently, the obtained material was used as a filament for 3D printing, i.e., by fused deposition modeling (FDM) technique. The physicochemical properties of the obtained filaments were determined, such as morphology (roughness), moisture sorption ability, thermal properties, and mechanical performance (tensile and compressive strength). Importantly, the metal filler did not modify the thermal properties of the polyester matrix, indicating that the filament containing steel microfiller could be processed using the same parameters as for neat PETG. The thermal stability was slightly enhanced after steel powder addition (for 13 wt.% content, the temperature of 75% weight loss was 466 °C; for comparison, that for the reference sample was 446 °C). The reinforcing effect of steel microfiller was noted based on mechanical performance measurements. The steel particles acted as a stiffening agent; the highest maximal tensile strength was observed for the composite with 3 wt.% steel powder content (ca. 68 MPa). Further increasing the microfiller load resulted in a slight decrease in the value of this parameter. A different trend was reported considering the compressive strength, i.e., the value of this parameter increased with steel content. Based on the obtained results, the new PETG composites could be applied as structural materials.

Schlagwörter

Stichwörter der Autor:innen

316L steelPETGfilamentfused deposition modeling

Autor:innen und Institutionen

  • Faculty of Mechanical Engineering, Koszalin University of Technology, ul. Śniadeckich 2, 75-453 Koszalin, Poland.
  • Faculty of Maritime Technology and Transport, West Pomeranian University of Technology in Szczecin, Piastów 41, 71-065 Szczecin, Poland.
  • Faculty of Chemical Technology and Engineering, West Pomeranian University of Technology in Szczecin, Pułaskiego 10, 70-322 Szczecin, Poland.

ORCID-Profile: Piotr Zmuda Trzebiatowski, Tomasz Królikowski, Agnieszka Ubowska, Katarzyna Wilpiszewska

Förderung

  • Narodowa Agencja Wymiany Akademickiej
  • National Agency for Academic Exchange (NAWA), the project “Koszalin University of Technology as an active member of EU4Dual”,

Zitieren

APA

Zmuda Trzebiatowski, P., Królikowski, T., Ubowska, A., & Wilpiszewska, K. (2025). Preparation and Properties of PETG Filament Modified with a Metallic Additive. Materials, 18(6), 1203. https://doi.org/10.3390/ma18061203

Vancouver

Zmuda Trzebiatowski P, Królikowski T, Ubowska A, Wilpiszewska K. Preparation and Properties of PETG Filament Modified with a Metallic Additive. Materials. 2025;18(6):1203. doi:10.3390/ma18061203

BibTeX
@article{ZmudaTrzebiatowski2025,
  author = {Zmuda Trzebiatowski, Piotr and Królikowski, Tomasz and Ubowska, Agnieszka and Wilpiszewska, Katarzyna},
  title = {Preparation and Properties of PETG Filament Modified with a Metallic Additive},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {6},
  pages = {1203},
  doi = {10.3390/ma18061203}
}
Kostenlos starten →