EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Process Parameters Analysis in Diamond Wire Saw Cutting NdFeB Magnet

Chengwanli Peng, Guanzheng Li, Xingchun Zhang, Yufei Gao

Materials · 06.03.2025 · 18 (5) · 1173

DOI: 10.3390/ma18051173 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 06.03.2025. Verfasst von Chengwanli Peng und 3 weiteren Autor:innen. Beteiligte Einrichtung: SDU-ANU Joint Science College, Shandong University, Weihai 264209, China. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Science Foundation of Shandong Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Neodymium iron boron (NdFeB) magnetic materials are widely used in fields such as electronics, medical devices, power machinery, and hardware machinery. This paper conducted a three-factor and five-level orthogonal experiment on diamond wire saw cutting NdFeB to determine the influence degree of key factors such as workpiece feed rate, diamond wire speed, and workpiece processed size on the surface roughness Ra and waviness Wa of NdFeB slices. Further analysis was conducted on the influence of various parameters on the PV value (peak valley difference) of the waviness profile curve of the sawed surface. Finally, slicing processing was carried out under optimized process parameter combinations. The research results indicate that the primary and secondary order of process parameters affecting surface roughness Ra and waviness Wa is workpiece feed rate, wire speed, and sawed workpiece size, and the influence on the waviness PV value also shows a consistent trend. The optimal combination of processing parameters is workpiece feed rate of 0.1 mm·min−1, wire speed of 1600 m·min−1, and workpiece size of 10 mm. The obtained surface roughness Ra is 0.433 μm and the waviness Wa is 0.037 μm, respectively. The regression mathematical model for the waviness PV value is PV = 0.747 × vs−0.342 × vw0.546 × L0.109. The research results of this paper provide an experimental basis and guidance for optimizing process parameters of sawing NdFeB.

Schlagwörter

Stichwörter der Autor:innen

NdFeB magnetdiamond wire saworthogonal experimentprocess parameterssurface waviness

Autor:innen und Institutionen

  • SDU-ANU Joint Science College, Shandong University, Weihai 264209, China.
  • Key Laboratory of High Efficiency and Clean Mechanical Manufacture of MOE, School of Mechanical Engineering, Shandong University, Jinan 250061, China.
  • State Key Laboratory of Advanced Equipment and Technology for Metal Forming, Shandong University, Jinan 250061, China.
  • Shandong Key Laboratory of High Performance Tools and System, Shandong University, Jinan 250061, China.

Förderung

  • Natural Science Foundation of Shandong Province

Zitieren

APA

Peng, C., Li, G., Zhang, X., & Gao, Y. (2025). Process Parameters Analysis in Diamond Wire Saw Cutting NdFeB Magnet. Materials, 18(5), 1173. https://doi.org/10.3390/ma18051173

Vancouver

Peng C, Li G, Zhang X, Gao Y. Process Parameters Analysis in Diamond Wire Saw Cutting NdFeB Magnet. Materials. 2025;18(5):1173. doi:10.3390/ma18051173

BibTeX
@article{Peng2025,
  author = {Peng, Chengwanli and Li, Guanzheng and Zhang, Xingchun and Gao, Yufei},
  title = {Process Parameters Analysis in Diamond Wire Saw Cutting NdFeB Magnet},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {5},
  pages = {1173},
  doi = {10.3390/ma18051173}
}
Kostenlos starten →