EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Microstructure and Mechanical Properties of AlSi10MnMg Alloy with Increased Content of Recycled Scrap

Jaroslaw Piatkowski iD, Katarzyna Nowinska iD, Tomasz Matula iD, Grzegorz Siwiec, Michal Szucki iD, Beata Oleksiak iD

Materials · 01.03.2025 · 18 (5) · 1119

DOI: 10.3390/ma18051119 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 01.03.2025. Verfasst von Jaroslaw Piatkowski und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Material Technologies, Faculty of Materials Science, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice, Poland. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Increasing the share of circulating scrap in produced castings is not only due to optimizing production costs, but also the need to protect the environment realized by reducing production energy intensity, generating less waste, mitigating greenhouse gas emissions, and consuming fewer natural resources. However, this is associated with maintaining the required properties of castings and considering the impact of impurities on the formation of the structure of aluminum alloys. This research concerns the AlSi10MnMg alloy, which introduces 50 to 75% (every 5%) of circulating scrap. This alloy is one of the most commonly used for producing gravity and pressure die-castings (HPDC), including engine parts and transport structural elements. Based on microscopic research, it was found that the increase in scrap content causes an increase in the share of iron, which results in pre-eutectic (from about 0.45 wt.% to 0.7 wt.% Fe) or even primary crystallization of iron phases (over 0.7 wt.% Fe), mainly the plate–needle phase β-Al5FeSi. Its unfavorable morphology and size cause the formation of numerous shrinkage porosity areas, which has an impact on the reduction in mechanical properties (reduction in UTS and YS by approx. 16% and elongation by approx. 18%, compared to the AlSi10MnMg alloy with 50% scrap content). It was found that the increase in the share of recycled scrap (from 50 to 75%) can be used only when the manganese content is increased. Its effect is to change the morphology of the β-Al5FeSi phase into α-Al15(Fe,Mn)3Si2, whose crystallization occurs in the temperature range of 540 to 555 °C and increases slightly with increasing manganese addition. It is essential to consider the appropriate value of the Mn/Fe quotient, which should be about 1/2, because a higher value may cause the formation of a sludge factor. This work aimed to determine the limiting iron content (contained in the scrap) at which the sequence of the β-Al5FeSi phase release (pre-eutectic or primary crystallization) changes. This sequence mainly affects the form of morphology, the dimensions of the β-Fe phase, and the proportion of shrinkage porosity.

Schlagwörter

Stichwörter der Autor:innen

AlSiMnMg alloysiron contentmechanical propertiesmicrostructureporosityrecycled scrap

Autor:innen und Institutionen

  • Department of Material Technologies, Faculty of Materials Science, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice, Poland.
  • Department of Electrical Engineering and Automation in Industry, Faculty of Mining, Safety Engineering and Industrial Automation, Silesian University of Technology, ul. Akademicka 2, 41-100 Gliwice, Poland.
  • Department of Metallurgy and Recycling, Faculty of Materials Science, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice, Poland.
  • Foundry Institute, Technische Universität Bergakademie Freiberg, 4 Bernhard-von-Cotta-Str., 09599 Freiberg, Germany.
  • Department of Production Engineering, Faculty of Materials Science, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice, Poland.

ORCID-Profile: Jaroslaw Piatkowski, Katarzyna Nowinska, Tomasz Matula, Michal Szucki, Beata Oleksiak

Zitieren

APA

Piatkowski, J., Nowinska, K., Matula, T., Siwiec, G., Szucki, M., & Oleksiak, B. (2025). Microstructure and Mechanical Properties of AlSi10MnMg Alloy with Increased Content of Recycled Scrap. Materials, 18(5), 1119. https://doi.org/10.3390/ma18051119

Vancouver

Piatkowski J, Nowinska K, Matula T, Siwiec G, Szucki M, Oleksiak B. Microstructure and Mechanical Properties of AlSi10MnMg Alloy with Increased Content of Recycled Scrap. Materials. 2025;18(5):1119. doi:10.3390/ma18051119

BibTeX
@article{Piatkowski2025,
  author = {Piatkowski, Jaroslaw and Nowinska, Katarzyna and Matula, Tomasz and Siwiec, Grzegorz and Szucki, Michal and Oleksiak, Beata},
  title = {Microstructure and Mechanical Properties of AlSi10MnMg Alloy with Increased Content of Recycled Scrap},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {5},
  pages = {1119},
  doi = {10.3390/ma18051119}
}
Kostenlos starten →