EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Preparation and Characteristics of Porous Mullite Ceramics by 3D Printing and In-Situ Synthesis

Rina Wu, Chaochao Wang, Guodong Xu, Meiling Fan, Zhigang Huang, Tao Zeng, Xiaohong Wang

Materials · 21.02.2025 · 18 (5) · 956

DOI: 10.3390/ma18050956 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 21.02.2025. Verfasst von Rina Wu und 6 weiteren Autor:innen. Beteiligte Einrichtung: School of Materials Science and Chemical Engineering, Harbin University of Science and Technology, Harbin 150080, China. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In-situ porous mullite ceramics with varying pore size and porosity were fabricated using 3D printing. The pore size was controlled by adjusting the size of polymethyl methacrylate (PMMA) microspheres. The effect of sintering temperature on phase evolution was also examined. Additionally, the impact of PMMA microsphere size and content on the rheological properties of the printing inks was investigated. The results indicated that alumina and microsilica fully transformed into mullite at 1550 °C. The influence of PMMA microsphere content and size on the porosity, mechanical properties, and thermal conductivity of 3D-printed porous mullite ceramics was also studied. The 3D-printed porous mullite ceramic prepared with 15 μm PMMA microspheres exhibited a porosity of 44.38%, a flexural strength of 58.53 MPa, and a thermal conductivity of 2.21 W/(m·K). This printing strategy offers a simple and effective method for fabricating porous mullite ceramics.

Schlagwörter

Stichwörter der Autor:innen

3D printingflexural behaviorsmullite ceramicpore structurerheological property

Autor:innen und Institutionen

  • School of Materials Science and Chemical Engineering, Harbin University of Science and Technology, Harbin 150080, China.
  • Department of Civil and Environmental Engineering, College of Engineering, Shantou University, Shantou 515063, China.
  • Powerchina Jangxi Electric Power Design Institute Co., Ltd., Nanchang 330096, China.
  • Special Ceramics Advanced Manufacturing Engineering Technology Research Center of Guangdong Provincial University, Shantou 515063, China.

Förderung

  • National Natural Science Foundation of China

Zitieren

APA

Wu, R., Wang, C., Xu, G., Fan, M., Huang, Z., Zeng, T., & Wang, X. (2025). Preparation and Characteristics of Porous Mullite Ceramics by 3D Printing and In-Situ Synthesis. Materials, 18(5), 956. https://doi.org/10.3390/ma18050956

Vancouver

Wu R, Wang C, Xu G, Fan M, Huang Z, Zeng T, et al. Preparation and Characteristics of Porous Mullite Ceramics by 3D Printing and In-Situ Synthesis. Materials. 2025;18(5):956. doi:10.3390/ma18050956

BibTeX
@article{Wu2025,
  author = {Wu, Rina and Wang, Chaochao and Xu, Guodong and Fan, Meiling and Huang, Zhigang and Zeng, Tao and Wang, Xiaohong},
  title = {Preparation and Characteristics of Porous Mullite Ceramics by 3D Printing and In-Situ Synthesis},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {5},
  pages = {956},
  doi = {10.3390/ma18050956}
}
Kostenlos starten →