EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Evaluation of the Influence of Primary and Secondary Crystal Orientations and Selected Structural Characteristics on Creep Resistance in Single-Crystal Nickel-Based Turbine Blades

Kamil Gancarczyk iD, Robert Albrecht, Paweł Sułkowicz iD, Mirosław Szala iD, Mariusz Walczak iD

Materials · 20.02.2025 · 18 (5) · 919

DOI: 10.3390/ma18050919 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 20.02.2025. Verfasst von Kamil Gancarczyk und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Powstancow Warszawy Ave., 35…. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Minister of Science, European Union.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study evaluates the perfection of the crystal structure of single-crystal turbine blade castings made from the CMSX-4 nickel superalloy. The analysis included primary and secondary crystal orientation measurements using the Ω-scan method and the novel OD-EFG X-ray diffractometer. The selected microstructural parameters of the single crystals were also analyzed, including the assessment of stereological parameters and the degree of porosity. A creep test was performed according to standard procedures and under conditions simulating real operational environments. The model single-crystal turbine blades were manufactured using the Bridgman–Stockbarger method, with variable withdrawal rates of 1 and 3 mm/min. Heat treatment of the single-crystal castings involved solution treatment followed by double aging. The evaluation of structural perfection was carried out in three states: as-cast, after solution heat treatment, and after double aging. The crystallographic orientation of the blades was determined on both the airfoil and the root part. The study determined how crystallographic orientation and microstructural parameters influence the creep resistance of the castings. It was found that in the as-cast condition, the greatest influence on high creep strength has a small deviation of the primary and constant value of secondary crystal orientation along the height of the blade casting. After heat treatment, the highest creep resistance was obtained for the blade manufactured at a withdrawal rate at 1 mm/min.

Schlagwörter

Stichwörter der Autor:innen

creep resistancecrystal orientationsingle crystalsuperalloyturbine blades

Autor:innen und Institutionen

  • Department of Materials Science, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Powstancow Warszawy Ave., 35-959 Rzeszow, Poland.
  • Institute of Materials Science, University of Silesia in Katowice, 1a 75 Pulku Piechoty St., 41-500 Chorzow, Poland.
  • Department of Manufacturing Techniques and Automation, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Powstancow Warszawy Ave., 35-959 Rzeszow, Poland.
  • Department of Materials Engineering, Faculty of Mechanical Engineering, Lublin University of Technology, 36 Nadbystrzycka St., 20-618 Lublin, Poland.

ORCID-Profile: Kamil Gancarczyk, Paweł Sułkowicz, Mirosław Szala, Mariusz Walczak

Förderung

  • Minister of Science
  • European Union

Zitieren

APA

Gancarczyk, K., Albrecht, R., Sułkowicz, P., Szala, M., & Walczak, M. (2025). Evaluation of the Influence of Primary and Secondary Crystal Orientations and Selected Structural Characteristics on Creep Resistance in Single-Crystal Nickel-Based Turbine Blades. Materials, 18(5), 919. https://doi.org/10.3390/ma18050919

Vancouver

Gancarczyk K, Albrecht R, Sułkowicz P, Szala M, Walczak M. Evaluation of the Influence of Primary and Secondary Crystal Orientations and Selected Structural Characteristics on Creep Resistance in Single-Crystal Nickel-Based Turbine Blades. Materials. 2025;18(5):919. doi:10.3390/ma18050919

BibTeX
@article{Gancarczyk2025,
  author = {Gancarczyk, Kamil and Albrecht, Robert and Sułkowicz, Paweł and Szala, Mirosław and Walczak, Mariusz},
  title = {Evaluation of the Influence of Primary and Secondary Crystal Orientations and Selected Structural Characteristics on Creep Resistance in Single-Crystal Nickel-Based Turbine Blades},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {5},
  pages = {919},
  doi = {10.3390/ma18050919}
}
Kostenlos starten →