EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Flexural Strength and Surface Properties of 3D-Printed Denture Base Resins—Effect of Build Angle, Layer Thickness and Aging

Shaimaa Fouda iD, Wenjie Ji, Mohammed M Gad iD, Maram A AlGhamdi iD, Nadja Rohr iD

Materials · 19.02.2025 · 18 (4) · 913

DOI: 10.3390/ma18040913 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 19.02.2025. Verfasst von Shaimaa Fouda und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam 31441, Saudi Arabia. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A variety of printable resins for denture bases are available, without detailed instructions on print parameters. This study aimed to evaluate the effect of the printing build angle and the layer thickness of 3D-printed denture base resins before and after thermocyclic aging on flexural strength values and surface properties. The flexural strength, surface roughness (Ra, Rz) and hardness (HM, HV2) of two 3D-printed denture base resins (Formlabs (FL) and V-print dentbase, VOCO, (VC)) were therefore compared to a conventionally pressed cold-curing control material (PalaXpress (PP)). The specimens were printed at a 0°, 45° or 90° build angle and the layer thickness was varied for FL at 50 and 100 µm and evaluated before and after thermocyclic aging (N = 200; n = 10). Differences in flexural strength values were analyzed using multifactorial ANOVAs (α = 0.05). The build angle and aging significantly affected the flexural strength of the 3D-printed denture base resins (p < 0.05), while the layer thickness showed no effect for FL (p = 0.461). The required threshold value of 65 MPa defined by ISO 20795-1 was exceeded by PP (70.5 MPa ± 5.5 MPa), by FL when printed at 90° (69.3 MPa ± 7.7 MPa) and by VC at 0° (69.0 MPa ± 4.6 MPa). The choice of an appropriate build angle for each material and printing technology is crucial for the flexural strength and consequently the clinical longevity of a printed denture base.

Schlagwörter

Stichwörter der Autor:innen

3D printingcomplete denturedenture basesflexural strengthmechanical testspolymethyl methacrylatesurface properties

Autor:innen und Institutionen

  • Department of Substitutive Dental Sciences, College of Dentistry, Imam Abdulrahman Bin Faisal University, Dammam 31441, Saudi Arabia.
  • Biomaterials and Technology, Department Research, University Center for Dental Medicine Basel UZB, University of Basel, Mattenstrasse 40, CH-4058 Basel, Switzerland.

ORCID-Profile: Shaimaa Fouda, Mohammed M Gad, Maram A AlGhamdi, Nadja Rohr

Zitieren

APA

Fouda, S., Ji, W., Gad, M. M., AlGhamdi, M. A., & Rohr, N. (2025). Flexural Strength and Surface Properties of 3D-Printed Denture Base Resins—Effect of Build Angle, Layer Thickness and Aging. Materials, 18(4), 913. https://doi.org/10.3390/ma18040913

Vancouver

Fouda S, Ji W, Gad MM, AlGhamdi MA, Rohr N. Flexural Strength and Surface Properties of 3D-Printed Denture Base Resins—Effect of Build Angle, Layer Thickness and Aging. Materials. 2025;18(4):913. doi:10.3390/ma18040913

BibTeX
@article{Fouda2025,
  author = {Fouda, Shaimaa and Ji, Wenjie and Gad, Mohammed M and AlGhamdi, Maram A and Rohr, Nadja},
  title = {Flexural Strength and Surface Properties of 3D-Printed Denture Base Resins—Effect of Build Angle, Layer Thickness and Aging},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {4},
  pages = {913},
  doi = {10.3390/ma18040913}
}
Kostenlos starten →