EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative Study on Extrusion 3D Printing of Solid Propellant Based on Plunger and Screw

Shixiong Song, Jiawei Shi, Quanbin Ren, Kai Miao, Min Tang, Hongbin Shi

Materials · 10.02.2025 · 18 (4) · 777

DOI: 10.3390/ma18040777 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 10.02.2025. Verfasst von Shixiong Song und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Astronautics, Northwestern Polytechnical University, Xi'an 710072, China. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Extrusion-based 3D printing holds great potential for manufacturing solid propellants. Among the various methods, screw- and plunger-based extrusion are the most frequently reported techniques for propellant 3D printing, each employing different extrusion mechanisms. This paper compares the flow characteristics of these two methods through a combination of simulations and experiments. Simulation results reveal that propellant slurry in a plunger extrusion device exhibits relatively stable flow characteristics, especially near the nozzle outlet, with high flow velocity, high shear rate, and low-pressure distribution. Compared to the screw-based device, the plunger extrusion achieves a more uniform outlet velocity. In contrast, the screw extrusion device produces more complex rheological behavior, with backflow observed in the gap between the screw and the extrusion channel wall. However, the average pressure in the flow channel for screw extrusion (3885.11 Pa) is notably lower than that of plunger extrusion (7292.92 Pa). Experimental results indicate that the printing quality of plunger extrusion is comparable to that of screw extrusion. These findings provide valuable insights into advancing extrusion-based 3D-printing processes for solid propellants.

Schlagwörter

Stichwörter der Autor:innen

3D printingcomparative studycomputational simulationplunger extrusionpropellant fabricationscrew extrusionsolid propellant

Autor:innen und Institutionen

  • School of Astronautics, Northwestern Polytechnical University, Xi'an 710072, China.
  • The Institute of Xi'an Aerospace Solid Propulsion Technology, Xi'an 710025, China.
  • Academy of Aerospace Solid Propulsion Technology, Xi'an 710025, China.
  • School of Mechanical Engineering, Xi'an Jiaotong University, Xi'an 710049, China.

Förderung

  • National Key Research and Development Program

Zitieren

APA

Song, S., Shi, J., Ren, Q., Miao, K., Tang, M., & Shi, H. (2025). Comparative Study on Extrusion 3D Printing of Solid Propellant Based on Plunger and Screw. Materials, 18(4), 777. https://doi.org/10.3390/ma18040777

Vancouver

Song S, Shi J, Ren Q, Miao K, Tang M, Shi H. Comparative Study on Extrusion 3D Printing of Solid Propellant Based on Plunger and Screw. Materials. 2025;18(4):777. doi:10.3390/ma18040777

BibTeX
@article{Song2025,
  author = {Song, Shixiong and Shi, Jiawei and Ren, Quanbin and Miao, Kai and Tang, Min and Shi, Hongbin},
  title = {Comparative Study on Extrusion 3D Printing of Solid Propellant Based on Plunger and Screw},
  journal = {Materials},
  year = {2025},
  volume = {18},
  number = {4},
  pages = {777},
  doi = {10.3390/ma18040777}
}
Kostenlos starten →